I need the pin out for the Electronic Load Detector.

I have a Canadian Honda Civic (1996) that has no ELD. I have swapped
in a JDM B18C1 engine (Acura Integra GSR) and now my ECU has a light on
for ELD (Code 20)

I have purchased another fuse box from eBay that now has the ELD
connector however I do not know the order of the pins for inputs and
output.

1 wire is 12Volt + (Black/White)
1 Wire is Ground + (Black)
1 Wire is 5 Volt Output. (Red/Green)

Does anyone know the order of the wires?

Anyone in the USA should be able to just look at the bottom of there
fuse box. I'm sure someone in a shop has a harness lying around they
can look at.

 

In article <1115921241.589751.35520@o13g2000cwo.googlegroups. com>,
google@canadiangeek.net wrote:

> I need the pin out for the Electronic Load Detector.
>
> I have a Canadian Honda Civic (1996) that has no ELD. I have swapped
> in a JDM B18C1 engine (Acura Integra GSR) and now my ECU has a light on
> for ELD (Code 20)
>
> I have purchased another fuse box from eBay that now has the ELD
> connector however I do not know the order of the pins for inputs and
> output.
>
> 1 wire is 12Volt + (Black/White)
> 1 Wire is Ground + (Black)
> 1 Wire is 5 Volt Output. (Red/Green)
>
> Does anyone know the order of the wires?
>
> Anyone in the USA should be able to just look at the bottom of there
> fuse box. I'm sure someone in a shop has a harness lying around they
> can look at.

I have the wire harness pinouts:

IG1 Black/White Pin 1 ELD
GND Black Pin 2 ELD
EL Green/Red Pin 3 ELD -> Pin 16 ECM/PCM Connector D


ELD 3P harness connector (C354):
-----
----|---|----
| 1 | 2 | 3 |
-------------
I G E
G N L
1 D


I can't find a picture of the ELD in the repair manual so I don't know
what to do if it has solder lugs or a non-standard jack on it.

 

In article <1115921241.589751.35520@o13g2000cwo.googlegroups. com>,
google@canadiangeek.net wrote:

> I need the pin out for the Electronic Load Detector.
>
> I have a Canadian Honda Civic (1996) that has no ELD. I have swapped
> in a JDM B18C1 engine (Acura Integra GSR) and now my ECU has a light on
> for ELD (Code 20)
>
> I have purchased another fuse box from eBay that now has the ELD
> connector however I do not know the order of the pins for inputs and
> output.
>
> 1 wire is 12Volt + (Black/White)
> 1 Wire is Ground + (Black)
> 1 Wire is 5 Volt Output. (Red/Green)
>
> Does anyone know the order of the wires?
>
> Anyone in the USA should be able to just look at the bottom of there
> fuse box. I'm sure someone in a shop has a harness lying around they
> can look at.

I have the wire harness pinouts:

IG1 Black/White Pin 1 ELD
GND Black Pin 2 ELD
EL Green/Red Pin 3 ELD -> Pin 16 ECM/PCM Connector D


ELD 3P harness connector (C354):
-----
----|---|----
| 1 | 2 | 3 |
-------------
I G E
G N L
1 D


I can't find a picture of the ELD in the repair manual so I don't know
what to do if it has solder lugs or a non-standard jack on it.

 

Thanks. I will give this a shot today.

it has a connector that is supposed to fit however I dont have the
connector so I will just use the leads as solder lugs.

 

Thanks. I will give this a shot today.

it has a connector that is supposed to fit however I dont have the
connector so I will just use the leads as solder lugs.