What is the proper way to hold the crankshaft from turning,while removing
the crankshaft bolt on an 89 Prelude?

 

I have tried the Impact gun with 150 psi and no luck. the problem is holding
the crankshaft from turning.
"Stephen Bigelow" <sbigelowXLS@rogers.com> wrote in message
news:uQmKa.14010$H9q1.2257@news04.bloor.is.net.cab le.rogers.com...
>
> "Mark" <debmar@eglr.net> wrote in message
> news:vfju0fieei3ed2@corp.supernews.com...
> > What is the proper way to hold the crankshaft from turning,while
removing
> > the crankshaft bolt on an 89 Prelude?
>
> Impact gun at your local friendly garage. Pass him a ten spot after the
nice
> man is done.
>
>

 

Me too.....then I took it to my fav shop. 3/4" gun...buuuu-ring!
Done like dinner.

Make sure you don't have too many disconnects in your line, they restrict
airflow a bunch. 150 at the pump doesn't mean 150 at the gun.


"Mark" <debmar@eglr.net> wrote in message
news:vfjuo26bbb2v19@corp.supernews.com...
> I have tried the Impact gun with 150 psi and no luck. the problem is
holding
> the crankshaft from turning.
> "Stephen Bigelow" <sbigelowXLS@rogers.com> wrote in message
> news:uQmKa.14010$H9q1.2257@news04.bloor.is.net.cab le.rogers.com...
> >
> > "Mark" <debmar@eglr.net> wrote in message
> > news:vfju0fieei3ed2@corp.supernews.com...
> > > What is the proper way to hold the crankshaft from turning,while
> removing
> > > the crankshaft bolt on an 89 Prelude?
> >
> > Impact gun at your local friendly garage. Pass him a ten spot after the
> nice
> > man is done.
> >
> >
>
>

 

This topic comes up often. I have pasted a copy of thread from March 03:


"I had the same problem on a 94 last month. If it has the hex shaped recess
in
the damper then there is a holder tool available from the auto specialty
online stores. My 94 has the holes around the edge type. Someone in this
newsgroup (see below) suggested I make a holder tool from a couple foot long
pipe with two bolts inserted. I found a piece of angle iron and inserted the

hardened bolts in it, it worked really well. The bolt loosens
counterclockwise so if you let the holder tool swing up against the lower
control arm it shouldn't damage anything. It is tightened to 130 ft/lbs. so
you will need a hefty breaker bar and decent access. I worked throungh the
drivers side wheel well with the car elevated on jack stands.

Here is the thread on this idea:

MikeWrite wrote:

> > Folks,
> >
> > Any suggestions for breaking the crank pulley bolt loose?
>
> Try this: stand next to the car, take a deep breath, clench your fists, and

> scream at the top of your lungs, "G** D*** THIS F***ING PULLEY BOLT!!!!!"
> The bolt won't come off, but you'll feel better.
>
> Then try this: http://mikewrite.home.mindspring.com/crankpulley.html
>
> Mike

Another person used a rachet as a holder, this idea did not work for me:
http://www.crxsi.com/resources/repai...e_timing_belt/

Some others suggested removing the starter motor to insert a large srewdriver

into the teeth of the flywheel, I was afraid of breaking flywheel teeth.

I have also read an impact wrench with 500-1000 ft/lb capability can break it

free. I have a cheapy that couldn't do it.

Good luck!

robad1 wrote:

> I am trying to change the timing belt on my wife's 91 1.5L Honda Civic. I
> can't get the bolt loose on the crankshaft pulley. Help!
> Thanks in advance.
> Robad1



Mark wrote:

> What is the proper way to hold the crankshaft from turning,while removing
> the crankshaft bolt on an 89 Prelude?

 

On Wed, 25 Jun 2003 15:29:33 -0400, "Mark" <debmar@eglr.net> wrote:

>What is the proper way to hold the crankshaft from turning,while removing
>the crankshaft bolt on an 89 Prelude?

its kinda crude, but in a jam once, I took a long power bar and a
socket, put the socket on the crank bolt, the powerpar then reached
out to the ground. then turned the car over with the starter.
but beware, this has all the makings of a disaster.
>

 

Actually, that's one of the techniques to use.

Of course, you shouldn't have motor mounts that might be stressed too
much (depends on their design) since the engine will torque a bit away
from the frame, especially if the crankshaft bolt won't give! This
technique didn't work for me though (the rubber motor mount broke and
so the engine didn't hold fast).

I ended up calling up one of those guys who go out and change
18-wheeler truck tires (mobile tire guys, who usually have a serious
air tool compressor on their trucks)...I supplied the correct 1/2"
drive metric socket and he loosened it for me.

Good luck,

John D.



Smanning <smanning@roadrunner.nf.net> wrote in message news:<tfdofvovt5jtbcmklrf2dcs9ppgv32e38o@4ax.com>. ..
> On Wed, 25 Jun 2003 15:29:33 -0400, "Mark" <debmar@eglr.net> wrote:
>
> >What is the proper way to hold the crankshaft from turning,while removing
> >the crankshaft bolt on an 89 Prelude?
>
> its kinda crude, but in a jam once, I took a long power bar and a
> socket, put the socket on the crank bolt, the powerpar then reached
> out to the ground. then turned the car over with the starter.
> but beware, this has all the makings of a disaster.
> >

 

When you say "one of the techniques to use" Who's techniques?Should the bar
me able to swing and gain momentum,or placed tight to the floor before
engaging starter?Aside from motor mount damage,What else can happen?
"John D." <jcdech@hotmail.com> wrote in message
news:e821bab6.0306271203.6f721131@posting.google.c om...
> Actually, that's one of the techniques to use.
>
> Of course, you shouldn't have motor mounts that might be stressed too
> much (depends on their design) since the engine will torque a bit away
> from the frame, especially if the crankshaft bolt won't give! This
> technique didn't work for me though (the rubber motor mount broke and
> so the engine didn't hold fast).
>
> I ended up calling up one of those guys who go out and change
> 18-wheeler truck tires (mobile tire guys, who usually have a serious
> air tool compressor on their trucks)...I supplied the correct 1/2"
> drive metric socket and he loosened it for me.
>
> Good luck,
>
> John D.
>
>
>
> Smanning <smanning@roadrunner.nf.net> wrote in message
news:<tfdofvovt5jtbcmklrf2dcs9ppgv32e38o@4ax.com>. ..
> > On Wed, 25 Jun 2003 15:29:33 -0400, "Mark" <debmar@eglr.net> wrote:
> >
> > >What is the proper way to hold the crankshaft from turning,while
removing
> > >the crankshaft bolt on an 89 Prelude?
> >
> > its kinda crude, but in a jam once, I took a long power bar and a
> > socket, put the socket on the crank bolt, the powerpar then reached
> > out to the ground. then turned the car over with the starter.
> > but beware, this has all the makings of a disaster.
> > >