"Randolph" <trash@junkmail.com> wrote:
> I have no particular knowledge of the '94 Accord, but I would think
> the
> least painful would be to remove the stereo and tap into the wiring
> harness that plugs in at the back of the stereo.
>
> http://tinyurl.com/3wh3a (leads to http://www.installdr.com) will tell
> you how to remove the stereo. It also says the wire is brown with
> white
> stripe, same as right rear speaker negative. I believe this is wrong,
> the factory manual says YEL/WHT for the antenna trigger (and BRN/WHT
> for
> the right rear speaker negative).

I do have the '94 Accord service manual and using that I've already
replaced the radio once, so I know how to do it. However, I'm not sure
the best place is at that wiring harness to make the splice for the
toggle switch. Oh, and yes, you're right about the color coding of the
antenna trigger wire: it is YEL/WHT at the antenna end. WHT/BLU is for
the constant battery voltage there.

Rudy

 

"R. P." wrote:
>
> "Randolph" <trash@junkmail.com> wrote:
> > I have no particular knowledge of the '94 Accord, but I would think
> > the
> > least painful would be to remove the stereo and tap into the wiring
> > harness that plugs in at the back of the stereo.

> I do have the '94 Accord service manual and using that I've already
> replaced the radio once, so I know how to do it. However, I'm not sure
> the best place is at that wiring harness to make the splice for the
> toggle switch. Oh, and yes, you're right about the color coding of the
> antenna trigger wire: it is YEL/WHT at the antenna end. WHT/BLU is for
> the constant battery voltage there.

If you put in an after-market stereo, you probably used an adapter
harness that plugs in between the stereo and the original plug on the
car wiring harness. If so, I would splice the toggle switch into this
adapter harness.

 

"R. P." wrote:
>
> "Randolph" <trash@junkmail.com> wrote:
> > I have no particular knowledge of the '94 Accord, but I would think
> > the
> > least painful would be to remove the stereo and tap into the wiring
> > harness that plugs in at the back of the stereo.

> I do have the '94 Accord service manual and using that I've already
> replaced the radio once, so I know how to do it. However, I'm not sure
> the best place is at that wiring harness to make the splice for the
> toggle switch. Oh, and yes, you're right about the color coding of the
> antenna trigger wire: it is YEL/WHT at the antenna end. WHT/BLU is for
> the constant battery voltage there.

If you put in an after-market stereo, you probably used an adapter
harness that plugs in between the stereo and the original plug on the
car wiring harness. If so, I would splice the toggle switch into this
adapter harness.

 

"Randolph" <trash@junkmail.com> wrote:
> If you put in an after-market stereo, you probably used an adapter
> harness that plugs in between the stereo and the original plug on the
> car wiring harness. If so, I would splice the toggle switch into this
> adapter harness.

Actually, I installed the same model AM/FM radio as the original
was, so I needed no adapter harness. I got the replacement radio from a
junked car.

Rudy

 

"Randolph" <trash@junkmail.com> wrote:
> If you put in an after-market stereo, you probably used an adapter
> harness that plugs in between the stereo and the original plug on the
> car wiring harness. If so, I would splice the toggle switch into this
> adapter harness.

Actually, I installed the same model AM/FM radio as the original
was, so I needed no adapter harness. I got the replacement radio from a
junked car.

Rudy