integra help
09-14-2003 | 07:58 PM
#2
Guest
Posts: n/a
Re: integra help
kenny b wrote:
>
> I have a Acura Integra (89) with a 1.4 engine. I'm trying to get the
> harmonic balancer bolt off, could someone tell me if its a reg. thrd or a
> left hand thrd.
> thanks, kenny b
The crank pulley bolt has regular right hand threads (counter clockwise to
loosen). You will either need a strong impact gun or a pulley holding tool if
you're trying to loosen it by hand. If the '89 integra does not have the 50 mm
hex opening for the pulley holding tool (available at places like Tool Town),
then you can fabricate a tool to fit in the holes in the pulley. Essentially,
you get a length of angle iron (about 2 feet or so) or other sturdy steel and
drill two holes in it. For my '88 Civic I drilled the holes 3 inches apart.
This allowed the bolts inserted through the steel to lock into the holes
skipping a hole in between. On my Civic the holes are 12 mm in diameter. You
can use 12 mm bolts or you may have better luck using 7/16 inch bolts (11.11 mm)
as they will allow for a little margin of error with respect to the location of
the holes you drilled in the steel bar. Try to use fine threaded bolts. You
can even use some heat shrink tubing over the bolts to help protect the pulley.
Another option is to thread some nuts onto the bolts from the back side of the
pulley to help hold it but be sure not to over tighten them, just hand tight.
Another option which is less successful is to clamp an old alternator belt
around the pulley with vise grips. You then clamp the other end to the
suspension. Sometimes, if you're lucky, this works. Other times, the belt just
breaks. I personally think you'll be better off going with a pulley holding
tool.
Eric
>
> I have a Acura Integra (89) with a 1.4 engine. I'm trying to get the
> harmonic balancer bolt off, could someone tell me if its a reg. thrd or a
> left hand thrd.
> thanks, kenny b
The crank pulley bolt has regular right hand threads (counter clockwise to
loosen). You will either need a strong impact gun or a pulley holding tool if
you're trying to loosen it by hand. If the '89 integra does not have the 50 mm
hex opening for the pulley holding tool (available at places like Tool Town),
then you can fabricate a tool to fit in the holes in the pulley. Essentially,
you get a length of angle iron (about 2 feet or so) or other sturdy steel and
drill two holes in it. For my '88 Civic I drilled the holes 3 inches apart.
This allowed the bolts inserted through the steel to lock into the holes
skipping a hole in between. On my Civic the holes are 12 mm in diameter. You
can use 12 mm bolts or you may have better luck using 7/16 inch bolts (11.11 mm)
as they will allow for a little margin of error with respect to the location of
the holes you drilled in the steel bar. Try to use fine threaded bolts. You
can even use some heat shrink tubing over the bolts to help protect the pulley.
Another option is to thread some nuts onto the bolts from the back side of the
pulley to help hold it but be sure not to over tighten them, just hand tight.
Another option which is less successful is to clamp an old alternator belt
around the pulley with vise grips. You then clamp the other end to the
suspension. Sometimes, if you're lucky, this works. Other times, the belt just
breaks. I personally think you'll be better off going with a pulley holding
tool.
Eric
09-14-2003 | 07:58 PM
#3
Guest
Posts: n/a
Re: integra help
kenny b wrote:
>
> I have a Acura Integra (89) with a 1.4 engine. I'm trying to get the
> harmonic balancer bolt off, could someone tell me if its a reg. thrd or a
> left hand thrd.
> thanks, kenny b
The crank pulley bolt has regular right hand threads (counter clockwise to
loosen). You will either need a strong impact gun or a pulley holding tool if
you're trying to loosen it by hand. If the '89 integra does not have the 50 mm
hex opening for the pulley holding tool (available at places like Tool Town),
then you can fabricate a tool to fit in the holes in the pulley. Essentially,
you get a length of angle iron (about 2 feet or so) or other sturdy steel and
drill two holes in it. For my '88 Civic I drilled the holes 3 inches apart.
This allowed the bolts inserted through the steel to lock into the holes
skipping a hole in between. On my Civic the holes are 12 mm in diameter. You
can use 12 mm bolts or you may have better luck using 7/16 inch bolts (11.11 mm)
as they will allow for a little margin of error with respect to the location of
the holes you drilled in the steel bar. Try to use fine threaded bolts. You
can even use some heat shrink tubing over the bolts to help protect the pulley.
Another option is to thread some nuts onto the bolts from the back side of the
pulley to help hold it but be sure not to over tighten them, just hand tight.
Another option which is less successful is to clamp an old alternator belt
around the pulley with vise grips. You then clamp the other end to the
suspension. Sometimes, if you're lucky, this works. Other times, the belt just
breaks. I personally think you'll be better off going with a pulley holding
tool.
Eric
>
> I have a Acura Integra (89) with a 1.4 engine. I'm trying to get the
> harmonic balancer bolt off, could someone tell me if its a reg. thrd or a
> left hand thrd.
> thanks, kenny b
The crank pulley bolt has regular right hand threads (counter clockwise to
loosen). You will either need a strong impact gun or a pulley holding tool if
you're trying to loosen it by hand. If the '89 integra does not have the 50 mm
hex opening for the pulley holding tool (available at places like Tool Town),
then you can fabricate a tool to fit in the holes in the pulley. Essentially,
you get a length of angle iron (about 2 feet or so) or other sturdy steel and
drill two holes in it. For my '88 Civic I drilled the holes 3 inches apart.
This allowed the bolts inserted through the steel to lock into the holes
skipping a hole in between. On my Civic the holes are 12 mm in diameter. You
can use 12 mm bolts or you may have better luck using 7/16 inch bolts (11.11 mm)
as they will allow for a little margin of error with respect to the location of
the holes you drilled in the steel bar. Try to use fine threaded bolts. You
can even use some heat shrink tubing over the bolts to help protect the pulley.
Another option is to thread some nuts onto the bolts from the back side of the
pulley to help hold it but be sure not to over tighten them, just hand tight.
Another option which is less successful is to clamp an old alternator belt
around the pulley with vise grips. You then clamp the other end to the
suspension. Sometimes, if you're lucky, this works. Other times, the belt just
breaks. I personally think you'll be better off going with a pulley holding
tool.
Eric
09-14-2003 | 07:58 PM
#4
Guest
Posts: n/a
Re: integra help
kenny b wrote:
>
> I have a Acura Integra (89) with a 1.4 engine. I'm trying to get the
> harmonic balancer bolt off, could someone tell me if its a reg. thrd or a
> left hand thrd.
> thanks, kenny b
The crank pulley bolt has regular right hand threads (counter clockwise to
loosen). You will either need a strong impact gun or a pulley holding tool if
you're trying to loosen it by hand. If the '89 integra does not have the 50 mm
hex opening for the pulley holding tool (available at places like Tool Town),
then you can fabricate a tool to fit in the holes in the pulley. Essentially,
you get a length of angle iron (about 2 feet or so) or other sturdy steel and
drill two holes in it. For my '88 Civic I drilled the holes 3 inches apart.
This allowed the bolts inserted through the steel to lock into the holes
skipping a hole in between. On my Civic the holes are 12 mm in diameter. You
can use 12 mm bolts or you may have better luck using 7/16 inch bolts (11.11 mm)
as they will allow for a little margin of error with respect to the location of
the holes you drilled in the steel bar. Try to use fine threaded bolts. You
can even use some heat shrink tubing over the bolts to help protect the pulley.
Another option is to thread some nuts onto the bolts from the back side of the
pulley to help hold it but be sure not to over tighten them, just hand tight.
Another option which is less successful is to clamp an old alternator belt
around the pulley with vise grips. You then clamp the other end to the
suspension. Sometimes, if you're lucky, this works. Other times, the belt just
breaks. I personally think you'll be better off going with a pulley holding
tool.
Eric
>
> I have a Acura Integra (89) with a 1.4 engine. I'm trying to get the
> harmonic balancer bolt off, could someone tell me if its a reg. thrd or a
> left hand thrd.
> thanks, kenny b
The crank pulley bolt has regular right hand threads (counter clockwise to
loosen). You will either need a strong impact gun or a pulley holding tool if
you're trying to loosen it by hand. If the '89 integra does not have the 50 mm
hex opening for the pulley holding tool (available at places like Tool Town),
then you can fabricate a tool to fit in the holes in the pulley. Essentially,
you get a length of angle iron (about 2 feet or so) or other sturdy steel and
drill two holes in it. For my '88 Civic I drilled the holes 3 inches apart.
This allowed the bolts inserted through the steel to lock into the holes
skipping a hole in between. On my Civic the holes are 12 mm in diameter. You
can use 12 mm bolts or you may have better luck using 7/16 inch bolts (11.11 mm)
as they will allow for a little margin of error with respect to the location of
the holes you drilled in the steel bar. Try to use fine threaded bolts. You
can even use some heat shrink tubing over the bolts to help protect the pulley.
Another option is to thread some nuts onto the bolts from the back side of the
pulley to help hold it but be sure not to over tighten them, just hand tight.
Another option which is less successful is to clamp an old alternator belt
around the pulley with vise grips. You then clamp the other end to the
suspension. Sometimes, if you're lucky, this works. Other times, the belt just
breaks. I personally think you'll be better off going with a pulley holding
tool.
Eric
09-14-2003 | 08:39 PM
#5
Guest
Posts: n/a
Re: integra help
thank u ... for your help... im gunna take ur ideas n hope they work!
"Eric" <say.no@spam.now> wrote in message news:3F6500B4.ABBF8EEC@spam.now...
> kenny b wrote:
> >
> > I have a Acura Integra (89) with a 1.4 engine. I'm trying to get the
> > harmonic balancer bolt off, could someone tell me if its a reg. thrd or
a
> > left hand thrd.
> > thanks, kenny b
>
> The crank pulley bolt has regular right hand threads (counter clockwise to
> loosen). You will either need a strong impact gun or a pulley holding
tool if
> you're trying to loosen it by hand. If the '89 integra does not have the
50 mm
> hex opening for the pulley holding tool (available at places like Tool
Town),
> then you can fabricate a tool to fit in the holes in the pulley.
Essentially,
> you get a length of angle iron (about 2 feet or so) or other sturdy steel
and
> drill two holes in it. For my '88 Civic I drilled the holes 3 inches
apart.
> This allowed the bolts inserted through the steel to lock into the holes
> skipping a hole in between. On my Civic the holes are 12 mm in diameter.
You
> can use 12 mm bolts or you may have better luck using 7/16 inch bolts
(11.11 mm)
> as they will allow for a little margin of error with respect to the
location of
> the holes you drilled in the steel bar. Try to use fine threaded bolts.
You
> can even use some heat shrink tubing over the bolts to help protect the
pulley.
> Another option is to thread some nuts onto the bolts from the back side of
the
> pulley to help hold it but be sure not to over tighten them, just hand
tight.
>
> Another option which is less successful is to clamp an old alternator belt
> around the pulley with vise grips. You then clamp the other end to the
> suspension. Sometimes, if you're lucky, this works. Other times, the
belt just
> breaks. I personally think you'll be better off going with a pulley
holding
> tool.
>
> Eric
"Eric" <say.no@spam.now> wrote in message news:3F6500B4.ABBF8EEC@spam.now...
> kenny b wrote:
> >
> > I have a Acura Integra (89) with a 1.4 engine. I'm trying to get the
> > harmonic balancer bolt off, could someone tell me if its a reg. thrd or
a
> > left hand thrd.
> > thanks, kenny b
>
> The crank pulley bolt has regular right hand threads (counter clockwise to
> loosen). You will either need a strong impact gun or a pulley holding
tool if
> you're trying to loosen it by hand. If the '89 integra does not have the
50 mm
> hex opening for the pulley holding tool (available at places like Tool
Town),
> then you can fabricate a tool to fit in the holes in the pulley.
Essentially,
> you get a length of angle iron (about 2 feet or so) or other sturdy steel
and
> drill two holes in it. For my '88 Civic I drilled the holes 3 inches
apart.
> This allowed the bolts inserted through the steel to lock into the holes
> skipping a hole in between. On my Civic the holes are 12 mm in diameter.
You
> can use 12 mm bolts or you may have better luck using 7/16 inch bolts
(11.11 mm)
> as they will allow for a little margin of error with respect to the
location of
> the holes you drilled in the steel bar. Try to use fine threaded bolts.
You
> can even use some heat shrink tubing over the bolts to help protect the
pulley.
> Another option is to thread some nuts onto the bolts from the back side of
the
> pulley to help hold it but be sure not to over tighten them, just hand
tight.
>
> Another option which is less successful is to clamp an old alternator belt
> around the pulley with vise grips. You then clamp the other end to the
> suspension. Sometimes, if you're lucky, this works. Other times, the
belt just
> breaks. I personally think you'll be better off going with a pulley
holding
> tool.
>
> Eric
09-14-2003 | 08:39 PM
#6
Guest
Posts: n/a
Re: integra help
thank u ... for your help... im gunna take ur ideas n hope they work!
"Eric" <say.no@spam.now> wrote in message news:3F6500B4.ABBF8EEC@spam.now...
> kenny b wrote:
> >
> > I have a Acura Integra (89) with a 1.4 engine. I'm trying to get the
> > harmonic balancer bolt off, could someone tell me if its a reg. thrd or
a
> > left hand thrd.
> > thanks, kenny b
>
> The crank pulley bolt has regular right hand threads (counter clockwise to
> loosen). You will either need a strong impact gun or a pulley holding
tool if
> you're trying to loosen it by hand. If the '89 integra does not have the
50 mm
> hex opening for the pulley holding tool (available at places like Tool
Town),
> then you can fabricate a tool to fit in the holes in the pulley.
Essentially,
> you get a length of angle iron (about 2 feet or so) or other sturdy steel
and
> drill two holes in it. For my '88 Civic I drilled the holes 3 inches
apart.
> This allowed the bolts inserted through the steel to lock into the holes
> skipping a hole in between. On my Civic the holes are 12 mm in diameter.
You
> can use 12 mm bolts or you may have better luck using 7/16 inch bolts
(11.11 mm)
> as they will allow for a little margin of error with respect to the
location of
> the holes you drilled in the steel bar. Try to use fine threaded bolts.
You
> can even use some heat shrink tubing over the bolts to help protect the
pulley.
> Another option is to thread some nuts onto the bolts from the back side of
the
> pulley to help hold it but be sure not to over tighten them, just hand
tight.
>
> Another option which is less successful is to clamp an old alternator belt
> around the pulley with vise grips. You then clamp the other end to the
> suspension. Sometimes, if you're lucky, this works. Other times, the
belt just
> breaks. I personally think you'll be better off going with a pulley
holding
> tool.
>
> Eric
"Eric" <say.no@spam.now> wrote in message news:3F6500B4.ABBF8EEC@spam.now...
> kenny b wrote:
> >
> > I have a Acura Integra (89) with a 1.4 engine. I'm trying to get the
> > harmonic balancer bolt off, could someone tell me if its a reg. thrd or
a
> > left hand thrd.
> > thanks, kenny b
>
> The crank pulley bolt has regular right hand threads (counter clockwise to
> loosen). You will either need a strong impact gun or a pulley holding
tool if
> you're trying to loosen it by hand. If the '89 integra does not have the
50 mm
> hex opening for the pulley holding tool (available at places like Tool
Town),
> then you can fabricate a tool to fit in the holes in the pulley.
Essentially,
> you get a length of angle iron (about 2 feet or so) or other sturdy steel
and
> drill two holes in it. For my '88 Civic I drilled the holes 3 inches
apart.
> This allowed the bolts inserted through the steel to lock into the holes
> skipping a hole in between. On my Civic the holes are 12 mm in diameter.
You
> can use 12 mm bolts or you may have better luck using 7/16 inch bolts
(11.11 mm)
> as they will allow for a little margin of error with respect to the
location of
> the holes you drilled in the steel bar. Try to use fine threaded bolts.
You
> can even use some heat shrink tubing over the bolts to help protect the
pulley.
> Another option is to thread some nuts onto the bolts from the back side of
the
> pulley to help hold it but be sure not to over tighten them, just hand
tight.
>
> Another option which is less successful is to clamp an old alternator belt
> around the pulley with vise grips. You then clamp the other end to the
> suspension. Sometimes, if you're lucky, this works. Other times, the
belt just
> breaks. I personally think you'll be better off going with a pulley
holding
> tool.
>
> Eric
09-14-2003 | 08:39 PM
#7
Guest
Posts: n/a
Re: integra help
thank u ... for your help... im gunna take ur ideas n hope they work!
"Eric" <say.no@spam.now> wrote in message news:3F6500B4.ABBF8EEC@spam.now...
> kenny b wrote:
> >
> > I have a Acura Integra (89) with a 1.4 engine. I'm trying to get the
> > harmonic balancer bolt off, could someone tell me if its a reg. thrd or
a
> > left hand thrd.
> > thanks, kenny b
>
> The crank pulley bolt has regular right hand threads (counter clockwise to
> loosen). You will either need a strong impact gun or a pulley holding
tool if
> you're trying to loosen it by hand. If the '89 integra does not have the
50 mm
> hex opening for the pulley holding tool (available at places like Tool
Town),
> then you can fabricate a tool to fit in the holes in the pulley.
Essentially,
> you get a length of angle iron (about 2 feet or so) or other sturdy steel
and
> drill two holes in it. For my '88 Civic I drilled the holes 3 inches
apart.
> This allowed the bolts inserted through the steel to lock into the holes
> skipping a hole in between. On my Civic the holes are 12 mm in diameter.
You
> can use 12 mm bolts or you may have better luck using 7/16 inch bolts
(11.11 mm)
> as they will allow for a little margin of error with respect to the
location of
> the holes you drilled in the steel bar. Try to use fine threaded bolts.
You
> can even use some heat shrink tubing over the bolts to help protect the
pulley.
> Another option is to thread some nuts onto the bolts from the back side of
the
> pulley to help hold it but be sure not to over tighten them, just hand
tight.
>
> Another option which is less successful is to clamp an old alternator belt
> around the pulley with vise grips. You then clamp the other end to the
> suspension. Sometimes, if you're lucky, this works. Other times, the
belt just
> breaks. I personally think you'll be better off going with a pulley
holding
> tool.
>
> Eric
"Eric" <say.no@spam.now> wrote in message news:3F6500B4.ABBF8EEC@spam.now...
> kenny b wrote:
> >
> > I have a Acura Integra (89) with a 1.4 engine. I'm trying to get the
> > harmonic balancer bolt off, could someone tell me if its a reg. thrd or
a
> > left hand thrd.
> > thanks, kenny b
>
> The crank pulley bolt has regular right hand threads (counter clockwise to
> loosen). You will either need a strong impact gun or a pulley holding
tool if
> you're trying to loosen it by hand. If the '89 integra does not have the
50 mm
> hex opening for the pulley holding tool (available at places like Tool
Town),
> then you can fabricate a tool to fit in the holes in the pulley.
Essentially,
> you get a length of angle iron (about 2 feet or so) or other sturdy steel
and
> drill two holes in it. For my '88 Civic I drilled the holes 3 inches
apart.
> This allowed the bolts inserted through the steel to lock into the holes
> skipping a hole in between. On my Civic the holes are 12 mm in diameter.
You
> can use 12 mm bolts or you may have better luck using 7/16 inch bolts
(11.11 mm)
> as they will allow for a little margin of error with respect to the
location of
> the holes you drilled in the steel bar. Try to use fine threaded bolts.
You
> can even use some heat shrink tubing over the bolts to help protect the
pulley.
> Another option is to thread some nuts onto the bolts from the back side of
the
> pulley to help hold it but be sure not to over tighten them, just hand
tight.
>
> Another option which is less successful is to clamp an old alternator belt
> around the pulley with vise grips. You then clamp the other end to the
> suspension. Sometimes, if you're lucky, this works. Other times, the
belt just
> breaks. I personally think you'll be better off going with a pulley
holding
> tool.
>
> Eric
Thread
Thread Starter
Forum
Replies
Last Post
Princess Leah
Car Care / Detailing / Paint / Visual Mods
0
04-28-2006 10:39 AM
JDMCRX
General Automotive Chat
11
05-10-2005 12:48 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)