CRV Valve Adjustment
03-21-2005 | 09:12 AM
#1
Guest
Posts: n/a
CRV Valve Adjustment
I brought my 98 CRV in for an oil change and he strongly suggested I do a
valve adjustment because they tend to tighten up and burn in this engine.
This struck me as strange for a few reasons. I had a 89 civic si and sold it
with 180,000 miles on it. In all that time I think the valves were adjusted
once. It was still running like a clock when I sold it with no apparent signs
of valve trouble. I mention that because I believe the CRV has basically the
same engine. I also thought that valves would only loosen up with time and
wear; not tighten. Is my logic sound or is there some truth to what I was
told???
Thanks.
Alex
valve adjustment because they tend to tighten up and burn in this engine.
This struck me as strange for a few reasons. I had a 89 civic si and sold it
with 180,000 miles on it. In all that time I think the valves were adjusted
once. It was still running like a clock when I sold it with no apparent signs
of valve trouble. I mention that because I believe the CRV has basically the
same engine. I also thought that valves would only loosen up with time and
wear; not tighten. Is my logic sound or is there some truth to what I was
told???
Thanks.
Alex
03-21-2005 | 09:51 AM
#2
Guest
Posts: n/a
Re: CRV Valve Adjustment
The 89 Civic is an SOHC engine, and the CRV is a DOHC engine... so comparing
the valve train between the engines is not going to give you the info you
need.
My experience is that in most Honda engines, the intake valves get looser
over time and the exhaust valves get tighter. It just depends what part of
the valve is wearing the most.
I would recommend adjusting that valves whenever the owner's manual suggests
it, unless Honda has release a revised schedule.
"Alex" <colenzae@suscom.net> wrote in message
news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>I brought my 98 CRV in for an oil change and he strongly suggested I do a
> valve adjustment because they tend to tighten up and burn in this engine.
> This struck me as strange for a few reasons. I had a 89 civic si and sold
> it
> with 180,000 miles on it. In all that time I think the valves were
> adjusted
> once. It was still running like a clock when I sold it with no apparent
> signs
> of valve trouble. I mention that because I believe the CRV has basically
> the
> same engine. I also thought that valves would only loosen up with time and
> wear; not tighten. Is my logic sound or is there some truth to what I was
> told???
>
> Thanks.
>
> Alex
>
the valve train between the engines is not going to give you the info you
need.
My experience is that in most Honda engines, the intake valves get looser
over time and the exhaust valves get tighter. It just depends what part of
the valve is wearing the most.
I would recommend adjusting that valves whenever the owner's manual suggests
it, unless Honda has release a revised schedule.
"Alex" <colenzae@suscom.net> wrote in message
news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>I brought my 98 CRV in for an oil change and he strongly suggested I do a
> valve adjustment because they tend to tighten up and burn in this engine.
> This struck me as strange for a few reasons. I had a 89 civic si and sold
> it
> with 180,000 miles on it. In all that time I think the valves were
> adjusted
> once. It was still running like a clock when I sold it with no apparent
> signs
> of valve trouble. I mention that because I believe the CRV has basically
> the
> same engine. I also thought that valves would only loosen up with time and
> wear; not tighten. Is my logic sound or is there some truth to what I was
> told???
>
> Thanks.
>
> Alex
>
03-21-2005 | 09:51 AM
#3
Guest
Posts: n/a
Re: CRV Valve Adjustment
The 89 Civic is an SOHC engine, and the CRV is a DOHC engine... so comparing
the valve train between the engines is not going to give you the info you
need.
My experience is that in most Honda engines, the intake valves get looser
over time and the exhaust valves get tighter. It just depends what part of
the valve is wearing the most.
I would recommend adjusting that valves whenever the owner's manual suggests
it, unless Honda has release a revised schedule.
"Alex" <colenzae@suscom.net> wrote in message
news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>I brought my 98 CRV in for an oil change and he strongly suggested I do a
> valve adjustment because they tend to tighten up and burn in this engine.
> This struck me as strange for a few reasons. I had a 89 civic si and sold
> it
> with 180,000 miles on it. In all that time I think the valves were
> adjusted
> once. It was still running like a clock when I sold it with no apparent
> signs
> of valve trouble. I mention that because I believe the CRV has basically
> the
> same engine. I also thought that valves would only loosen up with time and
> wear; not tighten. Is my logic sound or is there some truth to what I was
> told???
>
> Thanks.
>
> Alex
>
the valve train between the engines is not going to give you the info you
need.
My experience is that in most Honda engines, the intake valves get looser
over time and the exhaust valves get tighter. It just depends what part of
the valve is wearing the most.
I would recommend adjusting that valves whenever the owner's manual suggests
it, unless Honda has release a revised schedule.
"Alex" <colenzae@suscom.net> wrote in message
news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>I brought my 98 CRV in for an oil change and he strongly suggested I do a
> valve adjustment because they tend to tighten up and burn in this engine.
> This struck me as strange for a few reasons. I had a 89 civic si and sold
> it
> with 180,000 miles on it. In all that time I think the valves were
> adjusted
> once. It was still running like a clock when I sold it with no apparent
> signs
> of valve trouble. I mention that because I believe the CRV has basically
> the
> same engine. I also thought that valves would only loosen up with time and
> wear; not tighten. Is my logic sound or is there some truth to what I was
> told???
>
> Thanks.
>
> Alex
>
03-21-2005 | 10:19 AM
#4
Guest
Posts: n/a
Re: CRV Valve Adjustment
On Mon, 21 Mar 2005 09:51:47 -0500, Jafir Elkurd wrote
(in article <WbB%d.1836$Qz.490@okepread05>):
> The 89 Civic is an SOHC engine, and the CRV is a DOHC engine... so comparing
> the valve train between the engines is not going to give you the info you
> need.
>
> My experience is that in most Honda engines, the intake valves get looser
> over time and the exhaust valves get tighter. It just depends what part of
> the valve is wearing the most.
>
> I would recommend adjusting that valves whenever the owner's manual suggests
> it, unless Honda has release a revised schedule.
>
> "Alex" <colenzae@suscom.net> wrote in message
> news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>> I brought my 98 CRV in for an oil change and he strongly suggested I do a
>> valve adjustment because they tend to tighten up and burn in this engine.
>> This struck me as strange for a few reasons. I had a 89 civic si and sold
>> it
>> with 180,000 miles on it. In all that time I think the valves were
>> adjusted
>> once. It was still running like a clock when I sold it with no apparent
>> signs
>> of valve trouble. I mention that because I believe the CRV has basically
>> the
>> same engine. I also thought that valves would only loosen up with time and
>> wear; not tighten. Is my logic sound or is there some truth to what I was
>> told???
>>
>> Thanks.
>>
>> Alex
>>
>
>
Does anyone know the service interval?? We bought this car used with no
manuals.
Thanks,
Alex
(in article <WbB%d.1836$Qz.490@okepread05>):
> The 89 Civic is an SOHC engine, and the CRV is a DOHC engine... so comparing
> the valve train between the engines is not going to give you the info you
> need.
>
> My experience is that in most Honda engines, the intake valves get looser
> over time and the exhaust valves get tighter. It just depends what part of
> the valve is wearing the most.
>
> I would recommend adjusting that valves whenever the owner's manual suggests
> it, unless Honda has release a revised schedule.
>
> "Alex" <colenzae@suscom.net> wrote in message
> news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>> I brought my 98 CRV in for an oil change and he strongly suggested I do a
>> valve adjustment because they tend to tighten up and burn in this engine.
>> This struck me as strange for a few reasons. I had a 89 civic si and sold
>> it
>> with 180,000 miles on it. In all that time I think the valves were
>> adjusted
>> once. It was still running like a clock when I sold it with no apparent
>> signs
>> of valve trouble. I mention that because I believe the CRV has basically
>> the
>> same engine. I also thought that valves would only loosen up with time and
>> wear; not tighten. Is my logic sound or is there some truth to what I was
>> told???
>>
>> Thanks.
>>
>> Alex
>>
>
>
Does anyone know the service interval?? We bought this car used with no
manuals.
Thanks,
Alex
03-21-2005 | 10:19 AM
#5
Guest
Posts: n/a
Re: CRV Valve Adjustment
On Mon, 21 Mar 2005 09:51:47 -0500, Jafir Elkurd wrote
(in article <WbB%d.1836$Qz.490@okepread05>):
> The 89 Civic is an SOHC engine, and the CRV is a DOHC engine... so comparing
> the valve train between the engines is not going to give you the info you
> need.
>
> My experience is that in most Honda engines, the intake valves get looser
> over time and the exhaust valves get tighter. It just depends what part of
> the valve is wearing the most.
>
> I would recommend adjusting that valves whenever the owner's manual suggests
> it, unless Honda has release a revised schedule.
>
> "Alex" <colenzae@suscom.net> wrote in message
> news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>> I brought my 98 CRV in for an oil change and he strongly suggested I do a
>> valve adjustment because they tend to tighten up and burn in this engine.
>> This struck me as strange for a few reasons. I had a 89 civic si and sold
>> it
>> with 180,000 miles on it. In all that time I think the valves were
>> adjusted
>> once. It was still running like a clock when I sold it with no apparent
>> signs
>> of valve trouble. I mention that because I believe the CRV has basically
>> the
>> same engine. I also thought that valves would only loosen up with time and
>> wear; not tighten. Is my logic sound or is there some truth to what I was
>> told???
>>
>> Thanks.
>>
>> Alex
>>
>
>
Does anyone know the service interval?? We bought this car used with no
manuals.
Thanks,
Alex
(in article <WbB%d.1836$Qz.490@okepread05>):
> The 89 Civic is an SOHC engine, and the CRV is a DOHC engine... so comparing
> the valve train between the engines is not going to give you the info you
> need.
>
> My experience is that in most Honda engines, the intake valves get looser
> over time and the exhaust valves get tighter. It just depends what part of
> the valve is wearing the most.
>
> I would recommend adjusting that valves whenever the owner's manual suggests
> it, unless Honda has release a revised schedule.
>
> "Alex" <colenzae@suscom.net> wrote in message
> news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>> I brought my 98 CRV in for an oil change and he strongly suggested I do a
>> valve adjustment because they tend to tighten up and burn in this engine.
>> This struck me as strange for a few reasons. I had a 89 civic si and sold
>> it
>> with 180,000 miles on it. In all that time I think the valves were
>> adjusted
>> once. It was still running like a clock when I sold it with no apparent
>> signs
>> of valve trouble. I mention that because I believe the CRV has basically
>> the
>> same engine. I also thought that valves would only loosen up with time and
>> wear; not tighten. Is my logic sound or is there some truth to what I was
>> told???
>>
>> Thanks.
>>
>> Alex
>>
>
>
Does anyone know the service interval?? We bought this car used with no
manuals.
Thanks,
Alex
03-21-2005 | 12:07 PM
#6
Guest
Posts: n/a
Re: CRV Valve Adjustment
Alex wrote:
> I brought my 98 CRV in for an oil change and he strongly suggested I do a
> valve adjustment because they tend to tighten up and burn in this engine.
> This struck me as strange for a few reasons. I had a 89 civic si and sold it
> with 180,000 miles on it. In all that time I think the valves were adjusted
> once. It was still running like a clock when I sold it with no apparent signs
> of valve trouble. I mention that because I believe the CRV has basically the
> same engine. I also thought that valves would only loosen up with time and
> wear; not tighten. Is my logic sound or is there some truth to what I was
> told???
>
> Thanks.
>
> Alex
>
---------------------------
The guy is right. The valves in the first generation CR-V tend to
tighten, and will burn valves. So you should get them adjusted asap,
since you don't know the history. The manual is wrong anyway, but you
should order one from your dealer to save time in front of your
computer. The concensus over at hondasuv.com is 50,000 Km, (30,000
miles)Ask to have them adjusted on the 'loose' side of the spec. The
sticker is under the hood with the specs on it.You don't need a Honda
dealer to do it. . .Just somebody who's good with imports (and the
engine has to be COLD).
Same service interval applies to the Dual Pump Fluid in the rear
differential, otherwise, you'll get an awful grinding / moaning noise
when you turn tight felt-hand U-turns. It may seem to come from the
front of the CR-V, but it's caused by the rear diff. It only takes a
litre, and is a DIY job. Instructions are at hondasuv.com, and other places.
P.S. Go to the original dealer and get them to print out all the
previous service work. They'll do that for you. They want you to be
their friend.
'Curly'
> I brought my 98 CRV in for an oil change and he strongly suggested I do a
> valve adjustment because they tend to tighten up and burn in this engine.
> This struck me as strange for a few reasons. I had a 89 civic si and sold it
> with 180,000 miles on it. In all that time I think the valves were adjusted
> once. It was still running like a clock when I sold it with no apparent signs
> of valve trouble. I mention that because I believe the CRV has basically the
> same engine. I also thought that valves would only loosen up with time and
> wear; not tighten. Is my logic sound or is there some truth to what I was
> told???
>
> Thanks.
>
> Alex
>
---------------------------
The guy is right. The valves in the first generation CR-V tend to
tighten, and will burn valves. So you should get them adjusted asap,
since you don't know the history. The manual is wrong anyway, but you
should order one from your dealer to save time in front of your
computer. The concensus over at hondasuv.com is 50,000 Km, (30,000
miles)Ask to have them adjusted on the 'loose' side of the spec. The
sticker is under the hood with the specs on it.You don't need a Honda
dealer to do it. . .Just somebody who's good with imports (and the
engine has to be COLD).
Same service interval applies to the Dual Pump Fluid in the rear
differential, otherwise, you'll get an awful grinding / moaning noise
when you turn tight felt-hand U-turns. It may seem to come from the
front of the CR-V, but it's caused by the rear diff. It only takes a
litre, and is a DIY job. Instructions are at hondasuv.com, and other places.
P.S. Go to the original dealer and get them to print out all the
previous service work. They'll do that for you. They want you to be
their friend.
'Curly'
03-21-2005 | 12:07 PM
#7
Guest
Posts: n/a
Re: CRV Valve Adjustment
Alex wrote:
> I brought my 98 CRV in for an oil change and he strongly suggested I do a
> valve adjustment because they tend to tighten up and burn in this engine.
> This struck me as strange for a few reasons. I had a 89 civic si and sold it
> with 180,000 miles on it. In all that time I think the valves were adjusted
> once. It was still running like a clock when I sold it with no apparent signs
> of valve trouble. I mention that because I believe the CRV has basically the
> same engine. I also thought that valves would only loosen up with time and
> wear; not tighten. Is my logic sound or is there some truth to what I was
> told???
>
> Thanks.
>
> Alex
>
---------------------------
The guy is right. The valves in the first generation CR-V tend to
tighten, and will burn valves. So you should get them adjusted asap,
since you don't know the history. The manual is wrong anyway, but you
should order one from your dealer to save time in front of your
computer. The concensus over at hondasuv.com is 50,000 Km, (30,000
miles)Ask to have them adjusted on the 'loose' side of the spec. The
sticker is under the hood with the specs on it.You don't need a Honda
dealer to do it. . .Just somebody who's good with imports (and the
engine has to be COLD).
Same service interval applies to the Dual Pump Fluid in the rear
differential, otherwise, you'll get an awful grinding / moaning noise
when you turn tight felt-hand U-turns. It may seem to come from the
front of the CR-V, but it's caused by the rear diff. It only takes a
litre, and is a DIY job. Instructions are at hondasuv.com, and other places.
P.S. Go to the original dealer and get them to print out all the
previous service work. They'll do that for you. They want you to be
their friend.
'Curly'
> I brought my 98 CRV in for an oil change and he strongly suggested I do a
> valve adjustment because they tend to tighten up and burn in this engine.
> This struck me as strange for a few reasons. I had a 89 civic si and sold it
> with 180,000 miles on it. In all that time I think the valves were adjusted
> once. It was still running like a clock when I sold it with no apparent signs
> of valve trouble. I mention that because I believe the CRV has basically the
> same engine. I also thought that valves would only loosen up with time and
> wear; not tighten. Is my logic sound or is there some truth to what I was
> told???
>
> Thanks.
>
> Alex
>
---------------------------
The guy is right. The valves in the first generation CR-V tend to
tighten, and will burn valves. So you should get them adjusted asap,
since you don't know the history. The manual is wrong anyway, but you
should order one from your dealer to save time in front of your
computer. The concensus over at hondasuv.com is 50,000 Km, (30,000
miles)Ask to have them adjusted on the 'loose' side of the spec. The
sticker is under the hood with the specs on it.You don't need a Honda
dealer to do it. . .Just somebody who's good with imports (and the
engine has to be COLD).
Same service interval applies to the Dual Pump Fluid in the rear
differential, otherwise, you'll get an awful grinding / moaning noise
when you turn tight felt-hand U-turns. It may seem to come from the
front of the CR-V, but it's caused by the rear diff. It only takes a
litre, and is a DIY job. Instructions are at hondasuv.com, and other places.
P.S. Go to the original dealer and get them to print out all the
previous service work. They'll do that for you. They want you to be
their friend.
'Curly'
03-21-2005 | 09:36 PM
#8
Guest
Posts: n/a
Re: CRV Valve Adjustment
I did a google on Honda Service intervals and there was an easy to
understand PDF file .Just as detailed as the factory manual.
Tom
"Alex" <colenzae@suscom.net> wrote in message
news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>I brought my 98 CRV in for an oil change and he strongly suggested I do a
> valve adjustment because they tend to tighten up and burn in this engine.
> This struck me as strange for a few reasons. I had a 89 civic si and sold
> it
> with 180,000 miles on it. In all that time I think the valves were
> adjusted
> once. It was still running like a clock when I sold it with no apparent
> signs
> of valve trouble. I mention that because I believe the CRV has basically
> the
> same engine. I also thought that valves would only loosen up with time and
> wear; not tighten. Is my logic sound or is there some truth to what I was
> told???
>
> Thanks.
>
> Alex
>
understand PDF file .Just as detailed as the factory manual.
Tom
"Alex" <colenzae@suscom.net> wrote in message
news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>I brought my 98 CRV in for an oil change and he strongly suggested I do a
> valve adjustment because they tend to tighten up and burn in this engine.
> This struck me as strange for a few reasons. I had a 89 civic si and sold
> it
> with 180,000 miles on it. In all that time I think the valves were
> adjusted
> once. It was still running like a clock when I sold it with no apparent
> signs
> of valve trouble. I mention that because I believe the CRV has basically
> the
> same engine. I also thought that valves would only loosen up with time and
> wear; not tighten. Is my logic sound or is there some truth to what I was
> told???
>
> Thanks.
>
> Alex
>
03-21-2005 | 09:36 PM
#9
Guest
Posts: n/a
Re: CRV Valve Adjustment
I did a google on Honda Service intervals and there was an easy to
understand PDF file .Just as detailed as the factory manual.
Tom
"Alex" <colenzae@suscom.net> wrote in message
news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>I brought my 98 CRV in for an oil change and he strongly suggested I do a
> valve adjustment because they tend to tighten up and burn in this engine.
> This struck me as strange for a few reasons. I had a 89 civic si and sold
> it
> with 180,000 miles on it. In all that time I think the valves were
> adjusted
> once. It was still running like a clock when I sold it with no apparent
> signs
> of valve trouble. I mention that because I believe the CRV has basically
> the
> same engine. I also thought that valves would only loosen up with time and
> wear; not tighten. Is my logic sound or is there some truth to what I was
> told???
>
> Thanks.
>
> Alex
>
understand PDF file .Just as detailed as the factory manual.
Tom
"Alex" <colenzae@suscom.net> wrote in message
news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>I brought my 98 CRV in for an oil change and he strongly suggested I do a
> valve adjustment because they tend to tighten up and burn in this engine.
> This struck me as strange for a few reasons. I had a 89 civic si and sold
> it
> with 180,000 miles on it. In all that time I think the valves were
> adjusted
> once. It was still running like a clock when I sold it with no apparent
> signs
> of valve trouble. I mention that because I believe the CRV has basically
> the
> same engine. I also thought that valves would only loosen up with time and
> wear; not tighten. Is my logic sound or is there some truth to what I was
> told???
>
> Thanks.
>
> Alex
>
03-22-2005 | 06:43 PM
#10
Guest
Posts: n/a
Re: CRV Valve Adjustment
twfsa wrote:
> I did a google on Honda Service intervals and there was an easy to
> understand PDF file .Just as detailed as the factory manual.
>
> Tom
---------------------
Could you provide a link? It would be nice to see if it's correct, or
just a reprint of the info that's in the Incorrect Honda manual. . .
'Curly'
> I did a google on Honda Service intervals and there was an easy to
> understand PDF file .Just as detailed as the factory manual.
>
> Tom
---------------------
Could you provide a link? It would be nice to see if it's correct, or
just a reprint of the info that's in the Incorrect Honda manual. . .
'Curly'
03-22-2005 | 06:43 PM
#11
Guest
Posts: n/a
Re: CRV Valve Adjustment
twfsa wrote:
> I did a google on Honda Service intervals and there was an easy to
> understand PDF file .Just as detailed as the factory manual.
>
> Tom
---------------------
Could you provide a link? It would be nice to see if it's correct, or
just a reprint of the info that's in the Incorrect Honda manual. . .
'Curly'
> I did a google on Honda Service intervals and there was an easy to
> understand PDF file .Just as detailed as the factory manual.
>
> Tom
---------------------
Could you provide a link? It would be nice to see if it's correct, or
just a reprint of the info that's in the Incorrect Honda manual. . .
'Curly'
03-23-2005 | 07:23 AM
#12
Guest
Posts: n/a
Re: CRV Valve Adjustment
I think this is the link https://www.ahm-ownerlink.com/user_profile.asp
Tom
"motsco_ _" <"motsco_ _"@interbaun.com> wrote in message
news:4240AD9F.7000602@interbaun.com...
> twfsa wrote:
>> I did a google on Honda Service intervals and there was an easy to
>> understand PDF file .Just as detailed as the factory manual.
>>
>> Tom
>
>
> ---------------------
>
> Could you provide a link? It would be nice to see if it's correct, or just
> a reprint of the info that's in the Incorrect Honda manual. . .
>
> 'Curly'
>
Tom
"motsco_ _" <"motsco_ _"@interbaun.com> wrote in message
news:4240AD9F.7000602@interbaun.com...
> twfsa wrote:
>> I did a google on Honda Service intervals and there was an easy to
>> understand PDF file .Just as detailed as the factory manual.
>>
>> Tom
>
>
> ---------------------
>
> Could you provide a link? It would be nice to see if it's correct, or just
> a reprint of the info that's in the Incorrect Honda manual. . .
>
> 'Curly'
>
03-23-2005 | 07:23 AM
#13
Guest
Posts: n/a
Re: CRV Valve Adjustment
I think this is the link https://www.ahm-ownerlink.com/user_profile.asp
Tom
"motsco_ _" <"motsco_ _"@interbaun.com> wrote in message
news:4240AD9F.7000602@interbaun.com...
> twfsa wrote:
>> I did a google on Honda Service intervals and there was an easy to
>> understand PDF file .Just as detailed as the factory manual.
>>
>> Tom
>
>
> ---------------------
>
> Could you provide a link? It would be nice to see if it's correct, or just
> a reprint of the info that's in the Incorrect Honda manual. . .
>
> 'Curly'
>
Tom
"motsco_ _" <"motsco_ _"@interbaun.com> wrote in message
news:4240AD9F.7000602@interbaun.com...
> twfsa wrote:
>> I did a google on Honda Service intervals and there was an easy to
>> understand PDF file .Just as detailed as the factory manual.
>>
>> Tom
>
>
> ---------------------
>
> Could you provide a link? It would be nice to see if it's correct, or just
> a reprint of the info that's in the Incorrect Honda manual. . .
>
> 'Curly'
>
03-24-2005 | 02:02 PM
#14
Guest
Posts: n/a
Re: CRV Valve Adjustment
On Mon, 21 Mar 2005 09:51:47 -0500, Jafir Elkurd wrote
(in article <WbB%d.1836$Qz.490@okepread05>):
> The 89 Civic is an SOHC engine, and the CRV is a DOHC engine... so comparing
> the valve train between the engines is not going to give you the info you
> need.
>
> My experience is that in most Honda engines, the intake valves get looser
> over time and the exhaust valves get tighter. It just depends what part of
> the valve is wearing the most.
>
> I would recommend adjusting that valves whenever the owner's manual suggests
> it, unless Honda has release a revised schedule.
>
> "Alex" <colenzae@suscom.net> wrote in message
> news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>> I brought my 98 CRV in for an oil change and he strongly suggested I do a
>> valve adjustment because they tend to tighten up and burn in this engine.
>> This struck me as strange for a few reasons. I had a 89 civic si and sold
>> it
>> with 180,000 miles on it. In all that time I think the valves were
>> adjusted
>> once. It was still running like a clock when I sold it with no apparent
>> signs
>> of valve trouble. I mention that because I believe the CRV has basically
>> the
>> same engine. I also thought that valves would only loosen up with time and
>> wear; not tighten. Is my logic sound or is there some truth to what I was
>> told???
>>
>> Thanks.
>>
>> Alex
>>
>
>
Is there any way to tell if the valves are too tight??
(in article <WbB%d.1836$Qz.490@okepread05>):
> The 89 Civic is an SOHC engine, and the CRV is a DOHC engine... so comparing
> the valve train between the engines is not going to give you the info you
> need.
>
> My experience is that in most Honda engines, the intake valves get looser
> over time and the exhaust valves get tighter. It just depends what part of
> the valve is wearing the most.
>
> I would recommend adjusting that valves whenever the owner's manual suggests
> it, unless Honda has release a revised schedule.
>
> "Alex" <colenzae@suscom.net> wrote in message
> news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>> I brought my 98 CRV in for an oil change and he strongly suggested I do a
>> valve adjustment because they tend to tighten up and burn in this engine.
>> This struck me as strange for a few reasons. I had a 89 civic si and sold
>> it
>> with 180,000 miles on it. In all that time I think the valves were
>> adjusted
>> once. It was still running like a clock when I sold it with no apparent
>> signs
>> of valve trouble. I mention that because I believe the CRV has basically
>> the
>> same engine. I also thought that valves would only loosen up with time and
>> wear; not tighten. Is my logic sound or is there some truth to what I was
>> told???
>>
>> Thanks.
>>
>> Alex
>>
>
>
Is there any way to tell if the valves are too tight??
03-24-2005 | 02:02 PM
#15
Guest
Posts: n/a
Re: CRV Valve Adjustment
On Mon, 21 Mar 2005 09:51:47 -0500, Jafir Elkurd wrote
(in article <WbB%d.1836$Qz.490@okepread05>):
> The 89 Civic is an SOHC engine, and the CRV is a DOHC engine... so comparing
> the valve train between the engines is not going to give you the info you
> need.
>
> My experience is that in most Honda engines, the intake valves get looser
> over time and the exhaust valves get tighter. It just depends what part of
> the valve is wearing the most.
>
> I would recommend adjusting that valves whenever the owner's manual suggests
> it, unless Honda has release a revised schedule.
>
> "Alex" <colenzae@suscom.net> wrote in message
> news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>> I brought my 98 CRV in for an oil change and he strongly suggested I do a
>> valve adjustment because they tend to tighten up and burn in this engine.
>> This struck me as strange for a few reasons. I had a 89 civic si and sold
>> it
>> with 180,000 miles on it. In all that time I think the valves were
>> adjusted
>> once. It was still running like a clock when I sold it with no apparent
>> signs
>> of valve trouble. I mention that because I believe the CRV has basically
>> the
>> same engine. I also thought that valves would only loosen up with time and
>> wear; not tighten. Is my logic sound or is there some truth to what I was
>> told???
>>
>> Thanks.
>>
>> Alex
>>
>
>
Is there any way to tell if the valves are too tight??
(in article <WbB%d.1836$Qz.490@okepread05>):
> The 89 Civic is an SOHC engine, and the CRV is a DOHC engine... so comparing
> the valve train between the engines is not going to give you the info you
> need.
>
> My experience is that in most Honda engines, the intake valves get looser
> over time and the exhaust valves get tighter. It just depends what part of
> the valve is wearing the most.
>
> I would recommend adjusting that valves whenever the owner's manual suggests
> it, unless Honda has release a revised schedule.
>
> "Alex" <colenzae@suscom.net> wrote in message
> news:0001HW.BE64407403CE0110F04075B0@news.suscom.n et...
>> I brought my 98 CRV in for an oil change and he strongly suggested I do a
>> valve adjustment because they tend to tighten up and burn in this engine.
>> This struck me as strange for a few reasons. I had a 89 civic si and sold
>> it
>> with 180,000 miles on it. In all that time I think the valves were
>> adjusted
>> once. It was still running like a clock when I sold it with no apparent
>> signs
>> of valve trouble. I mention that because I believe the CRV has basically
>> the
>> same engine. I also thought that valves would only loosen up with time and
>> wear; not tighten. Is my logic sound or is there some truth to what I was
>> told???
>>
>> Thanks.
>>
>> Alex
>>
>
>
Is there any way to tell if the valves are too tight??