Carb Adjustment
12-01-2003 | 04:51 PM
#1
Guest
Posts: n/a
Carb Adjustment
I bought a carb kit from AutoZone and put all that stuff (gaskets, o-rings,
etc) on my '87 Accord LX. I found a damaged choke opener diaphragm and
installed a new one from Majestic Honda.
Since the car would start at very high rpms (> 3000K) and stay there I
suspected vacuum leaks. I replaced most vacuum hoses I could lay my hands
on (making sure I connected everything back the right way; besides I have
the vacuum diagram). Also replaced the gasket between the intake manifold
and EFE heater (also added some gasket sealant) as well as the o-ring. And
set all the speed adjustment screws to the lowest setting.
Now the car starts but dies if I take the foot off the accelerator. As a
matter of fact, I can't just keep the accelerator depressed, I need to
continuously pump gas into the carburetor by pressing the accelerator as
soon as I notice that the engine is about to die. I checked the accelerator
pump and you can actually see a stream of gas go into the carburetor when
you press the accelerator. However I'm suspicious that a constant flow of
gas is not making it into the carburetor.
What adjustments do I need to make? (I'm doing this using Helm, Chilton and
Haynes manuals. I'm not a mechanic but am trying to learn by doing things
myself on this car.)
etc) on my '87 Accord LX. I found a damaged choke opener diaphragm and
installed a new one from Majestic Honda.
Since the car would start at very high rpms (> 3000K) and stay there I
suspected vacuum leaks. I replaced most vacuum hoses I could lay my hands
on (making sure I connected everything back the right way; besides I have
the vacuum diagram). Also replaced the gasket between the intake manifold
and EFE heater (also added some gasket sealant) as well as the o-ring. And
set all the speed adjustment screws to the lowest setting.
Now the car starts but dies if I take the foot off the accelerator. As a
matter of fact, I can't just keep the accelerator depressed, I need to
continuously pump gas into the carburetor by pressing the accelerator as
soon as I notice that the engine is about to die. I checked the accelerator
pump and you can actually see a stream of gas go into the carburetor when
you press the accelerator. However I'm suspicious that a constant flow of
gas is not making it into the carburetor.
What adjustments do I need to make? (I'm doing this using Helm, Chilton and
Haynes manuals. I'm not a mechanic but am trying to learn by doing things
myself on this car.)
12-01-2003 | 06:08 PM
#2
Guest
Posts: n/a
Re: Carb Adjustment
MC wrote:
>
> I bought a carb kit from AutoZone and put all that stuff (gaskets,
> o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> diaphragm and installed a new one from Majestic Honda.
>
> Since the car would start at very high rpms (> 3000K) and stay there I
> suspected vacuum leaks. I replaced most vacuum hoses I could lay my hands
> on (making sure I connected everything back the right way; besides I have
> the vacuum diagram). Also replaced the gasket between the intake manifold
> and EFE heater (also added some gasket sealant) as well as the o-ring.
> And set all the speed adjustment screws to the lowest setting.
>
> Now the car starts but dies if I take the foot off the accelerator. As a
> matter of fact, I can't just keep the accelerator depressed, I need to
> continuously pump gas into the carburetor by pressing the accelerator as
> soon as I notice that the engine is about to die. I checked the
> accelerator pump and you can actually see a stream of gas go into the
> carburetor when you press the accelerator. However I'm suspicious that a
> constant flow of gas is not making it into the carburetor.
>
> What adjustments do I need to make? (I'm doing this using Helm, Chilton
> and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> things myself on this car.)
Just a thought, but is your float level adjustment ok? The fuel should be
visible through the sight glass in the side of the carb and the level should
be at the black dot in the center of the sight glass.
Eric
>
> I bought a carb kit from AutoZone and put all that stuff (gaskets,
> o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> diaphragm and installed a new one from Majestic Honda.
>
> Since the car would start at very high rpms (> 3000K) and stay there I
> suspected vacuum leaks. I replaced most vacuum hoses I could lay my hands
> on (making sure I connected everything back the right way; besides I have
> the vacuum diagram). Also replaced the gasket between the intake manifold
> and EFE heater (also added some gasket sealant) as well as the o-ring.
> And set all the speed adjustment screws to the lowest setting.
>
> Now the car starts but dies if I take the foot off the accelerator. As a
> matter of fact, I can't just keep the accelerator depressed, I need to
> continuously pump gas into the carburetor by pressing the accelerator as
> soon as I notice that the engine is about to die. I checked the
> accelerator pump and you can actually see a stream of gas go into the
> carburetor when you press the accelerator. However I'm suspicious that a
> constant flow of gas is not making it into the carburetor.
>
> What adjustments do I need to make? (I'm doing this using Helm, Chilton
> and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> things myself on this car.)
Just a thought, but is your float level adjustment ok? The fuel should be
visible through the sight glass in the side of the carb and the level should
be at the black dot in the center of the sight glass.
Eric
12-01-2003 | 06:08 PM
#3
Guest
Posts: n/a
Re: Carb Adjustment
MC wrote:
>
> I bought a carb kit from AutoZone and put all that stuff (gaskets,
> o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> diaphragm and installed a new one from Majestic Honda.
>
> Since the car would start at very high rpms (> 3000K) and stay there I
> suspected vacuum leaks. I replaced most vacuum hoses I could lay my hands
> on (making sure I connected everything back the right way; besides I have
> the vacuum diagram). Also replaced the gasket between the intake manifold
> and EFE heater (also added some gasket sealant) as well as the o-ring.
> And set all the speed adjustment screws to the lowest setting.
>
> Now the car starts but dies if I take the foot off the accelerator. As a
> matter of fact, I can't just keep the accelerator depressed, I need to
> continuously pump gas into the carburetor by pressing the accelerator as
> soon as I notice that the engine is about to die. I checked the
> accelerator pump and you can actually see a stream of gas go into the
> carburetor when you press the accelerator. However I'm suspicious that a
> constant flow of gas is not making it into the carburetor.
>
> What adjustments do I need to make? (I'm doing this using Helm, Chilton
> and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> things myself on this car.)
Just a thought, but is your float level adjustment ok? The fuel should be
visible through the sight glass in the side of the carb and the level should
be at the black dot in the center of the sight glass.
Eric
>
> I bought a carb kit from AutoZone and put all that stuff (gaskets,
> o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> diaphragm and installed a new one from Majestic Honda.
>
> Since the car would start at very high rpms (> 3000K) and stay there I
> suspected vacuum leaks. I replaced most vacuum hoses I could lay my hands
> on (making sure I connected everything back the right way; besides I have
> the vacuum diagram). Also replaced the gasket between the intake manifold
> and EFE heater (also added some gasket sealant) as well as the o-ring.
> And set all the speed adjustment screws to the lowest setting.
>
> Now the car starts but dies if I take the foot off the accelerator. As a
> matter of fact, I can't just keep the accelerator depressed, I need to
> continuously pump gas into the carburetor by pressing the accelerator as
> soon as I notice that the engine is about to die. I checked the
> accelerator pump and you can actually see a stream of gas go into the
> carburetor when you press the accelerator. However I'm suspicious that a
> constant flow of gas is not making it into the carburetor.
>
> What adjustments do I need to make? (I'm doing this using Helm, Chilton
> and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> things myself on this car.)
Just a thought, but is your float level adjustment ok? The fuel should be
visible through the sight glass in the side of the carb and the level should
be at the black dot in the center of the sight glass.
Eric
12-01-2003 | 06:08 PM
#4
Guest
Posts: n/a
Re: Carb Adjustment
MC wrote:
>
> I bought a carb kit from AutoZone and put all that stuff (gaskets,
> o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> diaphragm and installed a new one from Majestic Honda.
>
> Since the car would start at very high rpms (> 3000K) and stay there I
> suspected vacuum leaks. I replaced most vacuum hoses I could lay my hands
> on (making sure I connected everything back the right way; besides I have
> the vacuum diagram). Also replaced the gasket between the intake manifold
> and EFE heater (also added some gasket sealant) as well as the o-ring.
> And set all the speed adjustment screws to the lowest setting.
>
> Now the car starts but dies if I take the foot off the accelerator. As a
> matter of fact, I can't just keep the accelerator depressed, I need to
> continuously pump gas into the carburetor by pressing the accelerator as
> soon as I notice that the engine is about to die. I checked the
> accelerator pump and you can actually see a stream of gas go into the
> carburetor when you press the accelerator. However I'm suspicious that a
> constant flow of gas is not making it into the carburetor.
>
> What adjustments do I need to make? (I'm doing this using Helm, Chilton
> and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> things myself on this car.)
Just a thought, but is your float level adjustment ok? The fuel should be
visible through the sight glass in the side of the carb and the level should
be at the black dot in the center of the sight glass.
Eric
>
> I bought a carb kit from AutoZone and put all that stuff (gaskets,
> o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> diaphragm and installed a new one from Majestic Honda.
>
> Since the car would start at very high rpms (> 3000K) and stay there I
> suspected vacuum leaks. I replaced most vacuum hoses I could lay my hands
> on (making sure I connected everything back the right way; besides I have
> the vacuum diagram). Also replaced the gasket between the intake manifold
> and EFE heater (also added some gasket sealant) as well as the o-ring.
> And set all the speed adjustment screws to the lowest setting.
>
> Now the car starts but dies if I take the foot off the accelerator. As a
> matter of fact, I can't just keep the accelerator depressed, I need to
> continuously pump gas into the carburetor by pressing the accelerator as
> soon as I notice that the engine is about to die. I checked the
> accelerator pump and you can actually see a stream of gas go into the
> carburetor when you press the accelerator. However I'm suspicious that a
> constant flow of gas is not making it into the carburetor.
>
> What adjustments do I need to make? (I'm doing this using Helm, Chilton
> and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> things myself on this car.)
Just a thought, but is your float level adjustment ok? The fuel should be
visible through the sight glass in the side of the carb and the level should
be at the black dot in the center of the sight glass.
Eric
12-01-2003 | 06:08 PM
#5
Guest
Posts: n/a
Re: Carb Adjustment
MC wrote:
>
> I bought a carb kit from AutoZone and put all that stuff (gaskets,
> o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> diaphragm and installed a new one from Majestic Honda.
>
> Since the car would start at very high rpms (> 3000K) and stay there I
> suspected vacuum leaks. I replaced most vacuum hoses I could lay my hands
> on (making sure I connected everything back the right way; besides I have
> the vacuum diagram). Also replaced the gasket between the intake manifold
> and EFE heater (also added some gasket sealant) as well as the o-ring.
> And set all the speed adjustment screws to the lowest setting.
>
> Now the car starts but dies if I take the foot off the accelerator. As a
> matter of fact, I can't just keep the accelerator depressed, I need to
> continuously pump gas into the carburetor by pressing the accelerator as
> soon as I notice that the engine is about to die. I checked the
> accelerator pump and you can actually see a stream of gas go into the
> carburetor when you press the accelerator. However I'm suspicious that a
> constant flow of gas is not making it into the carburetor.
>
> What adjustments do I need to make? (I'm doing this using Helm, Chilton
> and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> things myself on this car.)
Just a thought, but is your float level adjustment ok? The fuel should be
visible through the sight glass in the side of the carb and the level should
be at the black dot in the center of the sight glass.
Eric
>
> I bought a carb kit from AutoZone and put all that stuff (gaskets,
> o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> diaphragm and installed a new one from Majestic Honda.
>
> Since the car would start at very high rpms (> 3000K) and stay there I
> suspected vacuum leaks. I replaced most vacuum hoses I could lay my hands
> on (making sure I connected everything back the right way; besides I have
> the vacuum diagram). Also replaced the gasket between the intake manifold
> and EFE heater (also added some gasket sealant) as well as the o-ring.
> And set all the speed adjustment screws to the lowest setting.
>
> Now the car starts but dies if I take the foot off the accelerator. As a
> matter of fact, I can't just keep the accelerator depressed, I need to
> continuously pump gas into the carburetor by pressing the accelerator as
> soon as I notice that the engine is about to die. I checked the
> accelerator pump and you can actually see a stream of gas go into the
> carburetor when you press the accelerator. However I'm suspicious that a
> constant flow of gas is not making it into the carburetor.
>
> What adjustments do I need to make? (I'm doing this using Helm, Chilton
> and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> things myself on this car.)
Just a thought, but is your float level adjustment ok? The fuel should be
visible through the sight glass in the side of the carb and the level should
be at the black dot in the center of the sight glass.
Eric
12-01-2003 | 07:41 PM
#6
Guest
Posts: n/a
Re: Carb Adjustment
The fuel is visible... it's a bit above center.
---
"Eric" <say.no@spam.now> wrote in message news:3FCBC9D4.9599CED6@spam.now...
> MC wrote:
> >
> > I bought a carb kit from AutoZone and put all that stuff (gaskets,
> > o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> > diaphragm and installed a new one from Majestic Honda.
> >
> > Since the car would start at very high rpms (> 3000K) and stay there I
> > suspected vacuum leaks. I replaced most vacuum hoses I could lay my
hands
> > on (making sure I connected everything back the right way; besides I
have
> > the vacuum diagram). Also replaced the gasket between the intake
manifold
> > and EFE heater (also added some gasket sealant) as well as the o-ring.
> > And set all the speed adjustment screws to the lowest setting.
> >
> > Now the car starts but dies if I take the foot off the accelerator. As
a
> > matter of fact, I can't just keep the accelerator depressed, I need to
> > continuously pump gas into the carburetor by pressing the accelerator as
> > soon as I notice that the engine is about to die. I checked the
> > accelerator pump and you can actually see a stream of gas go into the
> > carburetor when you press the accelerator. However I'm suspicious that
a
> > constant flow of gas is not making it into the carburetor.
> >
> > What adjustments do I need to make? (I'm doing this using Helm, Chilton
> > and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> > things myself on this car.)
>
> Just a thought, but is your float level adjustment ok? The fuel should be
> visible through the sight glass in the side of the carb and the level
should
> be at the black dot in the center of the sight glass.
>
> Eric
---
"Eric" <say.no@spam.now> wrote in message news:3FCBC9D4.9599CED6@spam.now...
> MC wrote:
> >
> > I bought a carb kit from AutoZone and put all that stuff (gaskets,
> > o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> > diaphragm and installed a new one from Majestic Honda.
> >
> > Since the car would start at very high rpms (> 3000K) and stay there I
> > suspected vacuum leaks. I replaced most vacuum hoses I could lay my
hands
> > on (making sure I connected everything back the right way; besides I
have
> > the vacuum diagram). Also replaced the gasket between the intake
manifold
> > and EFE heater (also added some gasket sealant) as well as the o-ring.
> > And set all the speed adjustment screws to the lowest setting.
> >
> > Now the car starts but dies if I take the foot off the accelerator. As
a
> > matter of fact, I can't just keep the accelerator depressed, I need to
> > continuously pump gas into the carburetor by pressing the accelerator as
> > soon as I notice that the engine is about to die. I checked the
> > accelerator pump and you can actually see a stream of gas go into the
> > carburetor when you press the accelerator. However I'm suspicious that
a
> > constant flow of gas is not making it into the carburetor.
> >
> > What adjustments do I need to make? (I'm doing this using Helm, Chilton
> > and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> > things myself on this car.)
>
> Just a thought, but is your float level adjustment ok? The fuel should be
> visible through the sight glass in the side of the carb and the level
should
> be at the black dot in the center of the sight glass.
>
> Eric
12-01-2003 | 07:41 PM
#7
Guest
Posts: n/a
Re: Carb Adjustment
The fuel is visible... it's a bit above center.
---
"Eric" <say.no@spam.now> wrote in message news:3FCBC9D4.9599CED6@spam.now...
> MC wrote:
> >
> > I bought a carb kit from AutoZone and put all that stuff (gaskets,
> > o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> > diaphragm and installed a new one from Majestic Honda.
> >
> > Since the car would start at very high rpms (> 3000K) and stay there I
> > suspected vacuum leaks. I replaced most vacuum hoses I could lay my
hands
> > on (making sure I connected everything back the right way; besides I
have
> > the vacuum diagram). Also replaced the gasket between the intake
manifold
> > and EFE heater (also added some gasket sealant) as well as the o-ring.
> > And set all the speed adjustment screws to the lowest setting.
> >
> > Now the car starts but dies if I take the foot off the accelerator. As
a
> > matter of fact, I can't just keep the accelerator depressed, I need to
> > continuously pump gas into the carburetor by pressing the accelerator as
> > soon as I notice that the engine is about to die. I checked the
> > accelerator pump and you can actually see a stream of gas go into the
> > carburetor when you press the accelerator. However I'm suspicious that
a
> > constant flow of gas is not making it into the carburetor.
> >
> > What adjustments do I need to make? (I'm doing this using Helm, Chilton
> > and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> > things myself on this car.)
>
> Just a thought, but is your float level adjustment ok? The fuel should be
> visible through the sight glass in the side of the carb and the level
should
> be at the black dot in the center of the sight glass.
>
> Eric
---
"Eric" <say.no@spam.now> wrote in message news:3FCBC9D4.9599CED6@spam.now...
> MC wrote:
> >
> > I bought a carb kit from AutoZone and put all that stuff (gaskets,
> > o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> > diaphragm and installed a new one from Majestic Honda.
> >
> > Since the car would start at very high rpms (> 3000K) and stay there I
> > suspected vacuum leaks. I replaced most vacuum hoses I could lay my
hands
> > on (making sure I connected everything back the right way; besides I
have
> > the vacuum diagram). Also replaced the gasket between the intake
manifold
> > and EFE heater (also added some gasket sealant) as well as the o-ring.
> > And set all the speed adjustment screws to the lowest setting.
> >
> > Now the car starts but dies if I take the foot off the accelerator. As
a
> > matter of fact, I can't just keep the accelerator depressed, I need to
> > continuously pump gas into the carburetor by pressing the accelerator as
> > soon as I notice that the engine is about to die. I checked the
> > accelerator pump and you can actually see a stream of gas go into the
> > carburetor when you press the accelerator. However I'm suspicious that
a
> > constant flow of gas is not making it into the carburetor.
> >
> > What adjustments do I need to make? (I'm doing this using Helm, Chilton
> > and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> > things myself on this car.)
>
> Just a thought, but is your float level adjustment ok? The fuel should be
> visible through the sight glass in the side of the carb and the level
should
> be at the black dot in the center of the sight glass.
>
> Eric
12-01-2003 | 07:41 PM
#8
Guest
Posts: n/a
Re: Carb Adjustment
The fuel is visible... it's a bit above center.
---
"Eric" <say.no@spam.now> wrote in message news:3FCBC9D4.9599CED6@spam.now...
> MC wrote:
> >
> > I bought a carb kit from AutoZone and put all that stuff (gaskets,
> > o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> > diaphragm and installed a new one from Majestic Honda.
> >
> > Since the car would start at very high rpms (> 3000K) and stay there I
> > suspected vacuum leaks. I replaced most vacuum hoses I could lay my
hands
> > on (making sure I connected everything back the right way; besides I
have
> > the vacuum diagram). Also replaced the gasket between the intake
manifold
> > and EFE heater (also added some gasket sealant) as well as the o-ring.
> > And set all the speed adjustment screws to the lowest setting.
> >
> > Now the car starts but dies if I take the foot off the accelerator. As
a
> > matter of fact, I can't just keep the accelerator depressed, I need to
> > continuously pump gas into the carburetor by pressing the accelerator as
> > soon as I notice that the engine is about to die. I checked the
> > accelerator pump and you can actually see a stream of gas go into the
> > carburetor when you press the accelerator. However I'm suspicious that
a
> > constant flow of gas is not making it into the carburetor.
> >
> > What adjustments do I need to make? (I'm doing this using Helm, Chilton
> > and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> > things myself on this car.)
>
> Just a thought, but is your float level adjustment ok? The fuel should be
> visible through the sight glass in the side of the carb and the level
should
> be at the black dot in the center of the sight glass.
>
> Eric
---
"Eric" <say.no@spam.now> wrote in message news:3FCBC9D4.9599CED6@spam.now...
> MC wrote:
> >
> > I bought a carb kit from AutoZone and put all that stuff (gaskets,
> > o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> > diaphragm and installed a new one from Majestic Honda.
> >
> > Since the car would start at very high rpms (> 3000K) and stay there I
> > suspected vacuum leaks. I replaced most vacuum hoses I could lay my
hands
> > on (making sure I connected everything back the right way; besides I
have
> > the vacuum diagram). Also replaced the gasket between the intake
manifold
> > and EFE heater (also added some gasket sealant) as well as the o-ring.
> > And set all the speed adjustment screws to the lowest setting.
> >
> > Now the car starts but dies if I take the foot off the accelerator. As
a
> > matter of fact, I can't just keep the accelerator depressed, I need to
> > continuously pump gas into the carburetor by pressing the accelerator as
> > soon as I notice that the engine is about to die. I checked the
> > accelerator pump and you can actually see a stream of gas go into the
> > carburetor when you press the accelerator. However I'm suspicious that
a
> > constant flow of gas is not making it into the carburetor.
> >
> > What adjustments do I need to make? (I'm doing this using Helm, Chilton
> > and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> > things myself on this car.)
>
> Just a thought, but is your float level adjustment ok? The fuel should be
> visible through the sight glass in the side of the carb and the level
should
> be at the black dot in the center of the sight glass.
>
> Eric
12-01-2003 | 07:41 PM
#9
Guest
Posts: n/a
Re: Carb Adjustment
The fuel is visible... it's a bit above center.
---
"Eric" <say.no@spam.now> wrote in message news:3FCBC9D4.9599CED6@spam.now...
> MC wrote:
> >
> > I bought a carb kit from AutoZone and put all that stuff (gaskets,
> > o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> > diaphragm and installed a new one from Majestic Honda.
> >
> > Since the car would start at very high rpms (> 3000K) and stay there I
> > suspected vacuum leaks. I replaced most vacuum hoses I could lay my
hands
> > on (making sure I connected everything back the right way; besides I
have
> > the vacuum diagram). Also replaced the gasket between the intake
manifold
> > and EFE heater (also added some gasket sealant) as well as the o-ring.
> > And set all the speed adjustment screws to the lowest setting.
> >
> > Now the car starts but dies if I take the foot off the accelerator. As
a
> > matter of fact, I can't just keep the accelerator depressed, I need to
> > continuously pump gas into the carburetor by pressing the accelerator as
> > soon as I notice that the engine is about to die. I checked the
> > accelerator pump and you can actually see a stream of gas go into the
> > carburetor when you press the accelerator. However I'm suspicious that
a
> > constant flow of gas is not making it into the carburetor.
> >
> > What adjustments do I need to make? (I'm doing this using Helm, Chilton
> > and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> > things myself on this car.)
>
> Just a thought, but is your float level adjustment ok? The fuel should be
> visible through the sight glass in the side of the carb and the level
should
> be at the black dot in the center of the sight glass.
>
> Eric
---
"Eric" <say.no@spam.now> wrote in message news:3FCBC9D4.9599CED6@spam.now...
> MC wrote:
> >
> > I bought a carb kit from AutoZone and put all that stuff (gaskets,
> > o-rings, etc) on my '87 Accord LX. I found a damaged choke opener
> > diaphragm and installed a new one from Majestic Honda.
> >
> > Since the car would start at very high rpms (> 3000K) and stay there I
> > suspected vacuum leaks. I replaced most vacuum hoses I could lay my
hands
> > on (making sure I connected everything back the right way; besides I
have
> > the vacuum diagram). Also replaced the gasket between the intake
manifold
> > and EFE heater (also added some gasket sealant) as well as the o-ring.
> > And set all the speed adjustment screws to the lowest setting.
> >
> > Now the car starts but dies if I take the foot off the accelerator. As
a
> > matter of fact, I can't just keep the accelerator depressed, I need to
> > continuously pump gas into the carburetor by pressing the accelerator as
> > soon as I notice that the engine is about to die. I checked the
> > accelerator pump and you can actually see a stream of gas go into the
> > carburetor when you press the accelerator. However I'm suspicious that
a
> > constant flow of gas is not making it into the carburetor.
> >
> > What adjustments do I need to make? (I'm doing this using Helm, Chilton
> > and Haynes manuals. I'm not a mechanic but am trying to learn by doing
> > things myself on this car.)
>
> Just a thought, but is your float level adjustment ok? The fuel should be
> visible through the sight glass in the side of the carb and the level
should
> be at the black dot in the center of the sight glass.
>
> Eric
12-01-2003 | 08:59 PM
#10
Guest
Posts: n/a
Re: Carb Adjustment
MC wrote:
>
> The fuel is visible... it's a bit above center.
OK, I'm thinking that you either have a really bad vacuum leak or your idle
circuit may be plugged. Have you tried running a propane enrichment test?
Another test you can do is to check for leaks at the carb base by spraying
with a little carb cleaner.
Eric
>
> The fuel is visible... it's a bit above center.
OK, I'm thinking that you either have a really bad vacuum leak or your idle
circuit may be plugged. Have you tried running a propane enrichment test?
Another test you can do is to check for leaks at the carb base by spraying
with a little carb cleaner.
Eric
12-01-2003 | 08:59 PM
#11
Guest
Posts: n/a
Re: Carb Adjustment
MC wrote:
>
> The fuel is visible... it's a bit above center.
OK, I'm thinking that you either have a really bad vacuum leak or your idle
circuit may be plugged. Have you tried running a propane enrichment test?
Another test you can do is to check for leaks at the carb base by spraying
with a little carb cleaner.
Eric
>
> The fuel is visible... it's a bit above center.
OK, I'm thinking that you either have a really bad vacuum leak or your idle
circuit may be plugged. Have you tried running a propane enrichment test?
Another test you can do is to check for leaks at the carb base by spraying
with a little carb cleaner.
Eric
12-01-2003 | 08:59 PM
#12
Guest
Posts: n/a
Re: Carb Adjustment
MC wrote:
>
> The fuel is visible... it's a bit above center.
OK, I'm thinking that you either have a really bad vacuum leak or your idle
circuit may be plugged. Have you tried running a propane enrichment test?
Another test you can do is to check for leaks at the carb base by spraying
with a little carb cleaner.
Eric
>
> The fuel is visible... it's a bit above center.
OK, I'm thinking that you either have a really bad vacuum leak or your idle
circuit may be plugged. Have you tried running a propane enrichment test?
Another test you can do is to check for leaks at the carb base by spraying
with a little carb cleaner.
Eric
12-01-2003 | 08:59 PM
#13
Guest
Posts: n/a
Re: Carb Adjustment
MC wrote:
>
> The fuel is visible... it's a bit above center.
OK, I'm thinking that you either have a really bad vacuum leak or your idle
circuit may be plugged. Have you tried running a propane enrichment test?
Another test you can do is to check for leaks at the carb base by spraying
with a little carb cleaner.
Eric
>
> The fuel is visible... it's a bit above center.
OK, I'm thinking that you either have a really bad vacuum leak or your idle
circuit may be plugged. Have you tried running a propane enrichment test?
Another test you can do is to check for leaks at the carb base by spraying
with a little carb cleaner.
Eric
12-01-2003 | 09:14 PM
#14
Guest
Posts: n/a
Re: Carb Adjustment
MC wrote:
>
> The fuel is visible... it's a bit above center.
OK, I'm thinking that you either have a really bad vacuum leak or your idle
circuit may be plugged. Have you tried running a propane enrichment test?
Another test you can do is to check for leaks at the carb base by spraying
with a little carb cleaner.
Eric
>
> The fuel is visible... it's a bit above center.
OK, I'm thinking that you either have a really bad vacuum leak or your idle
circuit may be plugged. Have you tried running a propane enrichment test?
Another test you can do is to check for leaks at the carb base by spraying
with a little carb cleaner.
Eric
12-01-2003 | 09:14 PM
#15
Guest
Posts: n/a
Re: Carb Adjustment
MC wrote:
>
> The fuel is visible... it's a bit above center.
OK, I'm thinking that you either have a really bad vacuum leak or your idle
circuit may be plugged. Have you tried running a propane enrichment test?
Another test you can do is to check for leaks at the carb base by spraying
with a little carb cleaner.
Eric
>
> The fuel is visible... it's a bit above center.
OK, I'm thinking that you either have a really bad vacuum leak or your idle
circuit may be plugged. Have you tried running a propane enrichment test?
Another test you can do is to check for leaks at the carb base by spraying
with a little carb cleaner.
Eric