96 Accord P0141
#2
Guest
Posts: n/a
Re: 96 Accord P0141
On 8/17/2006 6:06 AM Andy & Carol spake these words of knowledge:
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
I replaced one on my 2003 4-cyl Accord because of the same code, but I
suppose things have changed quite a bit in 7 model years.
On my car, it wasn't too bad, although I had to remove the right front
seat, per my Helms manual. It should be easier on yours, I would think.
Use an OEM part rather than aftermarket.
RFT!!!
Dave Kelsen
--
I always try to be modest; I'm very proud of that.
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
I replaced one on my 2003 4-cyl Accord because of the same code, but I
suppose things have changed quite a bit in 7 model years.
On my car, it wasn't too bad, although I had to remove the right front
seat, per my Helms manual. It should be easier on yours, I would think.
Use an OEM part rather than aftermarket.
RFT!!!
Dave Kelsen
--
I always try to be modest; I'm very proud of that.
#3
Guest
Posts: n/a
Re: 96 Accord P0141
On 8/17/2006 6:06 AM Andy & Carol spake these words of knowledge:
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
I replaced one on my 2003 4-cyl Accord because of the same code, but I
suppose things have changed quite a bit in 7 model years.
On my car, it wasn't too bad, although I had to remove the right front
seat, per my Helms manual. It should be easier on yours, I would think.
Use an OEM part rather than aftermarket.
RFT!!!
Dave Kelsen
--
I always try to be modest; I'm very proud of that.
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
I replaced one on my 2003 4-cyl Accord because of the same code, but I
suppose things have changed quite a bit in 7 model years.
On my car, it wasn't too bad, although I had to remove the right front
seat, per my Helms manual. It should be easier on yours, I would think.
Use an OEM part rather than aftermarket.
RFT!!!
Dave Kelsen
--
I always try to be modest; I'm very proud of that.
#4
Guest
Posts: n/a
Re: 96 Accord P0141
On 8/17/2006 6:06 AM Andy & Carol spake these words of knowledge:
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
I replaced one on my 2003 4-cyl Accord because of the same code, but I
suppose things have changed quite a bit in 7 model years.
On my car, it wasn't too bad, although I had to remove the right front
seat, per my Helms manual. It should be easier on yours, I would think.
Use an OEM part rather than aftermarket.
RFT!!!
Dave Kelsen
--
I always try to be modest; I'm very proud of that.
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
I replaced one on my 2003 4-cyl Accord because of the same code, but I
suppose things have changed quite a bit in 7 model years.
On my car, it wasn't too bad, although I had to remove the right front
seat, per my Helms manual. It should be easier on yours, I would think.
Use an OEM part rather than aftermarket.
RFT!!!
Dave Kelsen
--
I always try to be modest; I'm very proud of that.
#5
Guest
Posts: n/a
Re: 96 Accord P0141
"Andy & Carol" <aforn@worldnet.att.net> wrote in message
news:P4YEg.633581$Fs1.392849@bgtnsc05-news.ops.worldnet.att.net...
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
Other than the sensor, a large exhaust leak can cause the code. Most muffler
shops will do a free inspection in hopes of getting business if something
turns up; might be worth a visit. Otherwise you are probably stuck with
sensor replacement.
Mike
news:P4YEg.633581$Fs1.392849@bgtnsc05-news.ops.worldnet.att.net...
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
Other than the sensor, a large exhaust leak can cause the code. Most muffler
shops will do a free inspection in hopes of getting business if something
turns up; might be worth a visit. Otherwise you are probably stuck with
sensor replacement.
Mike
#6
Guest
Posts: n/a
Re: 96 Accord P0141
"Andy & Carol" <aforn@worldnet.att.net> wrote in message
news:P4YEg.633581$Fs1.392849@bgtnsc05-news.ops.worldnet.att.net...
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
Other than the sensor, a large exhaust leak can cause the code. Most muffler
shops will do a free inspection in hopes of getting business if something
turns up; might be worth a visit. Otherwise you are probably stuck with
sensor replacement.
Mike
news:P4YEg.633581$Fs1.392849@bgtnsc05-news.ops.worldnet.att.net...
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
Other than the sensor, a large exhaust leak can cause the code. Most muffler
shops will do a free inspection in hopes of getting business if something
turns up; might be worth a visit. Otherwise you are probably stuck with
sensor replacement.
Mike
#7
Guest
Posts: n/a
Re: 96 Accord P0141
"Andy & Carol" <aforn@worldnet.att.net> wrote in message
news:P4YEg.633581$Fs1.392849@bgtnsc05-news.ops.worldnet.att.net...
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
Other than the sensor, a large exhaust leak can cause the code. Most muffler
shops will do a free inspection in hopes of getting business if something
turns up; might be worth a visit. Otherwise you are probably stuck with
sensor replacement.
Mike
news:P4YEg.633581$Fs1.392849@bgtnsc05-news.ops.worldnet.att.net...
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
Other than the sensor, a large exhaust leak can cause the code. Most muffler
shops will do a free inspection in hopes of getting business if something
turns up; might be worth a visit. Otherwise you are probably stuck with
sensor replacement.
Mike
#8
Guest
Posts: n/a
Re: 96 Accord P0141
Dave Kelsen wrote:
> On 8/17/2006 6:06 AM Andy & Carol spake these words of knowledge:
>
>> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
>> won't reset. 4 cylinder engine. Anybody have any ideas?
>>
>> Is it the sensor heater itself, Is there a problem with these?
>> I will get in to it on Sat.
>> Andy
>
> I replaced one on my 2003 4-cyl Accord because of the same code, but I
> suppose things have changed quite a bit in 7 model years.
>
> On my car, it wasn't too bad, although I had to remove the right front
> seat, per my Helms manual. It should be easier on yours, I would think.
>
> Use an OEM part rather than aftermarket.
>
>
> RFT!!!
> Dave Kelsen
In many places in the USA you are covered by a mandatory emissions
warranty up to 8 years and 80,000 miles on emissions components. Many
people are not aware of this and pay out of pocket for covered items.
Check this:
http://www.epa.gov/otaq/consumer/warr95fs.txt
John
> On 8/17/2006 6:06 AM Andy & Carol spake these words of knowledge:
>
>> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
>> won't reset. 4 cylinder engine. Anybody have any ideas?
>>
>> Is it the sensor heater itself, Is there a problem with these?
>> I will get in to it on Sat.
>> Andy
>
> I replaced one on my 2003 4-cyl Accord because of the same code, but I
> suppose things have changed quite a bit in 7 model years.
>
> On my car, it wasn't too bad, although I had to remove the right front
> seat, per my Helms manual. It should be easier on yours, I would think.
>
> Use an OEM part rather than aftermarket.
>
>
> RFT!!!
> Dave Kelsen
In many places in the USA you are covered by a mandatory emissions
warranty up to 8 years and 80,000 miles on emissions components. Many
people are not aware of this and pay out of pocket for covered items.
Check this:
http://www.epa.gov/otaq/consumer/warr95fs.txt
John
#9
Guest
Posts: n/a
Re: 96 Accord P0141
Dave Kelsen wrote:
> On 8/17/2006 6:06 AM Andy & Carol spake these words of knowledge:
>
>> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
>> won't reset. 4 cylinder engine. Anybody have any ideas?
>>
>> Is it the sensor heater itself, Is there a problem with these?
>> I will get in to it on Sat.
>> Andy
>
> I replaced one on my 2003 4-cyl Accord because of the same code, but I
> suppose things have changed quite a bit in 7 model years.
>
> On my car, it wasn't too bad, although I had to remove the right front
> seat, per my Helms manual. It should be easier on yours, I would think.
>
> Use an OEM part rather than aftermarket.
>
>
> RFT!!!
> Dave Kelsen
In many places in the USA you are covered by a mandatory emissions
warranty up to 8 years and 80,000 miles on emissions components. Many
people are not aware of this and pay out of pocket for covered items.
Check this:
http://www.epa.gov/otaq/consumer/warr95fs.txt
John
> On 8/17/2006 6:06 AM Andy & Carol spake these words of knowledge:
>
>> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
>> won't reset. 4 cylinder engine. Anybody have any ideas?
>>
>> Is it the sensor heater itself, Is there a problem with these?
>> I will get in to it on Sat.
>> Andy
>
> I replaced one on my 2003 4-cyl Accord because of the same code, but I
> suppose things have changed quite a bit in 7 model years.
>
> On my car, it wasn't too bad, although I had to remove the right front
> seat, per my Helms manual. It should be easier on yours, I would think.
>
> Use an OEM part rather than aftermarket.
>
>
> RFT!!!
> Dave Kelsen
In many places in the USA you are covered by a mandatory emissions
warranty up to 8 years and 80,000 miles on emissions components. Many
people are not aware of this and pay out of pocket for covered items.
Check this:
http://www.epa.gov/otaq/consumer/warr95fs.txt
John
#10
Guest
Posts: n/a
Re: 96 Accord P0141
Dave Kelsen wrote:
> On 8/17/2006 6:06 AM Andy & Carol spake these words of knowledge:
>
>> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
>> won't reset. 4 cylinder engine. Anybody have any ideas?
>>
>> Is it the sensor heater itself, Is there a problem with these?
>> I will get in to it on Sat.
>> Andy
>
> I replaced one on my 2003 4-cyl Accord because of the same code, but I
> suppose things have changed quite a bit in 7 model years.
>
> On my car, it wasn't too bad, although I had to remove the right front
> seat, per my Helms manual. It should be easier on yours, I would think.
>
> Use an OEM part rather than aftermarket.
>
>
> RFT!!!
> Dave Kelsen
In many places in the USA you are covered by a mandatory emissions
warranty up to 8 years and 80,000 miles on emissions components. Many
people are not aware of this and pay out of pocket for covered items.
Check this:
http://www.epa.gov/otaq/consumer/warr95fs.txt
John
> On 8/17/2006 6:06 AM Andy & Carol spake these words of knowledge:
>
>> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
>> won't reset. 4 cylinder engine. Anybody have any ideas?
>>
>> Is it the sensor heater itself, Is there a problem with these?
>> I will get in to it on Sat.
>> Andy
>
> I replaced one on my 2003 4-cyl Accord because of the same code, but I
> suppose things have changed quite a bit in 7 model years.
>
> On my car, it wasn't too bad, although I had to remove the right front
> seat, per my Helms manual. It should be easier on yours, I would think.
>
> Use an OEM part rather than aftermarket.
>
>
> RFT!!!
> Dave Kelsen
In many places in the USA you are covered by a mandatory emissions
warranty up to 8 years and 80,000 miles on emissions components. Many
people are not aware of this and pay out of pocket for covered items.
Check this:
http://www.epa.gov/otaq/consumer/warr95fs.txt
John
#11
Guest
Posts: n/a
Re: 96 Accord P0141
Andy & Carol wrote:
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
The heater is integrated into the Ox sensor. It is a common failure on
a ten year old vehicle and shouldn't be a big deal to change as long as
you have access to it. I first remove the wiring to it and then use a
box end wrench to turn the sensor. I don't recall the size, but it
might be an SAE size rather than metric. Don't use an open end or other
wrench as that sucker might be corroded into place.
The secondary sensor is the one after the catalytic converter. There
are two, one before and one after. The one before the converter is the
actual feedback device for engine mixture adjustment. The one after the
converter is part of the car's self-monitoring emissions control system.
Also, do not mess with a universal replacement sensor featuring wire
splices. I've had bad luck with those. The secondary sensor is the one
after the catalytic converter. There are two, one before and one after.
The one before the converter is the actual feedback device for engine
mixture adjustment. The one after the converter is part of the car's
self-monitoring emissions control system.
You can get a Denso sensor for around $70 from rockauto.com. I buy many
of my parts there. You can also get a 5% discount from them through
8/22 by entering the discount code 44696037569. On Japanese cars I
generally use Densos and on European cars the Bosch sensors. Generally
there is no need to get a dealer part. However, do stay away from the
"universal" sensors.
Best of luck,
John
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
The heater is integrated into the Ox sensor. It is a common failure on
a ten year old vehicle and shouldn't be a big deal to change as long as
you have access to it. I first remove the wiring to it and then use a
box end wrench to turn the sensor. I don't recall the size, but it
might be an SAE size rather than metric. Don't use an open end or other
wrench as that sucker might be corroded into place.
The secondary sensor is the one after the catalytic converter. There
are two, one before and one after. The one before the converter is the
actual feedback device for engine mixture adjustment. The one after the
converter is part of the car's self-monitoring emissions control system.
Also, do not mess with a universal replacement sensor featuring wire
splices. I've had bad luck with those. The secondary sensor is the one
after the catalytic converter. There are two, one before and one after.
The one before the converter is the actual feedback device for engine
mixture adjustment. The one after the converter is part of the car's
self-monitoring emissions control system.
You can get a Denso sensor for around $70 from rockauto.com. I buy many
of my parts there. You can also get a 5% discount from them through
8/22 by entering the discount code 44696037569. On Japanese cars I
generally use Densos and on European cars the Bosch sensors. Generally
there is no need to get a dealer part. However, do stay away from the
"universal" sensors.
Best of luck,
John
#12
Guest
Posts: n/a
Re: 96 Accord P0141
Andy & Carol wrote:
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
The heater is integrated into the Ox sensor. It is a common failure on
a ten year old vehicle and shouldn't be a big deal to change as long as
you have access to it. I first remove the wiring to it and then use a
box end wrench to turn the sensor. I don't recall the size, but it
might be an SAE size rather than metric. Don't use an open end or other
wrench as that sucker might be corroded into place.
The secondary sensor is the one after the catalytic converter. There
are two, one before and one after. The one before the converter is the
actual feedback device for engine mixture adjustment. The one after the
converter is part of the car's self-monitoring emissions control system.
Also, do not mess with a universal replacement sensor featuring wire
splices. I've had bad luck with those. The secondary sensor is the one
after the catalytic converter. There are two, one before and one after.
The one before the converter is the actual feedback device for engine
mixture adjustment. The one after the converter is part of the car's
self-monitoring emissions control system.
You can get a Denso sensor for around $70 from rockauto.com. I buy many
of my parts there. You can also get a 5% discount from them through
8/22 by entering the discount code 44696037569. On Japanese cars I
generally use Densos and on European cars the Bosch sensors. Generally
there is no need to get a dealer part. However, do stay away from the
"universal" sensors.
Best of luck,
John
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
The heater is integrated into the Ox sensor. It is a common failure on
a ten year old vehicle and shouldn't be a big deal to change as long as
you have access to it. I first remove the wiring to it and then use a
box end wrench to turn the sensor. I don't recall the size, but it
might be an SAE size rather than metric. Don't use an open end or other
wrench as that sucker might be corroded into place.
The secondary sensor is the one after the catalytic converter. There
are two, one before and one after. The one before the converter is the
actual feedback device for engine mixture adjustment. The one after the
converter is part of the car's self-monitoring emissions control system.
Also, do not mess with a universal replacement sensor featuring wire
splices. I've had bad luck with those. The secondary sensor is the one
after the catalytic converter. There are two, one before and one after.
The one before the converter is the actual feedback device for engine
mixture adjustment. The one after the converter is part of the car's
self-monitoring emissions control system.
You can get a Denso sensor for around $70 from rockauto.com. I buy many
of my parts there. You can also get a 5% discount from them through
8/22 by entering the discount code 44696037569. On Japanese cars I
generally use Densos and on European cars the Bosch sensors. Generally
there is no need to get a dealer part. However, do stay away from the
"universal" sensors.
Best of luck,
John
#13
Guest
Posts: n/a
Re: 96 Accord P0141
Andy & Carol wrote:
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
The heater is integrated into the Ox sensor. It is a common failure on
a ten year old vehicle and shouldn't be a big deal to change as long as
you have access to it. I first remove the wiring to it and then use a
box end wrench to turn the sensor. I don't recall the size, but it
might be an SAE size rather than metric. Don't use an open end or other
wrench as that sucker might be corroded into place.
The secondary sensor is the one after the catalytic converter. There
are two, one before and one after. The one before the converter is the
actual feedback device for engine mixture adjustment. The one after the
converter is part of the car's self-monitoring emissions control system.
Also, do not mess with a universal replacement sensor featuring wire
splices. I've had bad luck with those. The secondary sensor is the one
after the catalytic converter. There are two, one before and one after.
The one before the converter is the actual feedback device for engine
mixture adjustment. The one after the converter is part of the car's
self-monitoring emissions control system.
You can get a Denso sensor for around $70 from rockauto.com. I buy many
of my parts there. You can also get a 5% discount from them through
8/22 by entering the discount code 44696037569. On Japanese cars I
generally use Densos and on European cars the Bosch sensors. Generally
there is no need to get a dealer part. However, do stay away from the
"universal" sensors.
Best of luck,
John
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
The heater is integrated into the Ox sensor. It is a common failure on
a ten year old vehicle and shouldn't be a big deal to change as long as
you have access to it. I first remove the wiring to it and then use a
box end wrench to turn the sensor. I don't recall the size, but it
might be an SAE size rather than metric. Don't use an open end or other
wrench as that sucker might be corroded into place.
The secondary sensor is the one after the catalytic converter. There
are two, one before and one after. The one before the converter is the
actual feedback device for engine mixture adjustment. The one after the
converter is part of the car's self-monitoring emissions control system.
Also, do not mess with a universal replacement sensor featuring wire
splices. I've had bad luck with those. The secondary sensor is the one
after the catalytic converter. There are two, one before and one after.
The one before the converter is the actual feedback device for engine
mixture adjustment. The one after the converter is part of the car's
self-monitoring emissions control system.
You can get a Denso sensor for around $70 from rockauto.com. I buy many
of my parts there. You can also get a 5% discount from them through
8/22 by entering the discount code 44696037569. On Japanese cars I
generally use Densos and on European cars the Bosch sensors. Generally
there is no need to get a dealer part. However, do stay away from the
"universal" sensors.
Best of luck,
John
#14
Guest
Posts: n/a
Re: 96 Accord P0141
Thank you, John, for the info, but I have 165,000 miles on the
Accord, and I must admit, enjoyable and trouble free!
I cant ask for much more!
Andy
"Andy & Carol" <aforn@worldnet.att.net> wrote in message
news:P4YEg.633581$Fs1.392849@bgtnsc05-news.ops.worldnet.att.net...
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
Accord, and I must admit, enjoyable and trouble free!
I cant ask for much more!
Andy
"Andy & Carol" <aforn@worldnet.att.net> wrote in message
news:P4YEg.633581$Fs1.392849@bgtnsc05-news.ops.worldnet.att.net...
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
#15
Guest
Posts: n/a
Re: 96 Accord P0141
Thank you, John, for the info, but I have 165,000 miles on the
Accord, and I must admit, enjoyable and trouble free!
I cant ask for much more!
Andy
"Andy & Carol" <aforn@worldnet.att.net> wrote in message
news:P4YEg.633581$Fs1.392849@bgtnsc05-news.ops.worldnet.att.net...
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>
Accord, and I must admit, enjoyable and trouble free!
I cant ask for much more!
Andy
"Andy & Carol" <aforn@worldnet.att.net> wrote in message
news:P4YEg.633581$Fs1.392849@bgtnsc05-news.ops.worldnet.att.net...
> P0141 Secondary Heated Oxygen Senser ckt malfunction..DTC
> won't reset. 4 cylinder engine. Anybody have any ideas?
>
> Is it the sensor heater itself, Is there a problem with these?
> I will get in to it on Sat.
> Andy
>
>
>