1990 accord torn rack boot
12-13-2006 | 06:45 PM
#2
Guest
Posts: n/a
Re: 1990 accord torn rack boot
etoyfixers@gmail.com wrote in news:1166040842.197701.272950
@n67g2000cwd.googlegroups.com:
> I just failed VA inspection because my right front rack boot is torn.
> Can I replace the boot myself?
>
Yes. It requires removal of the outer tie rod end.
When removing make 100% certain you count the threads and make sure you
reinstall it *precisely* the way it came off, otherwise you'll throw your
toe setting out.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
@n67g2000cwd.googlegroups.com:
> I just failed VA inspection because my right front rack boot is torn.
> Can I replace the boot myself?
>
Yes. It requires removal of the outer tie rod end.
When removing make 100% certain you count the threads and make sure you
reinstall it *precisely* the way it came off, otherwise you'll throw your
toe setting out.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
12-13-2006 | 06:45 PM
#3
Guest
Posts: n/a
Re: 1990 accord torn rack boot
etoyfixers@gmail.com wrote in news:1166040842.197701.272950
@n67g2000cwd.googlegroups.com:
> I just failed VA inspection because my right front rack boot is torn.
> Can I replace the boot myself?
>
Yes. It requires removal of the outer tie rod end.
When removing make 100% certain you count the threads and make sure you
reinstall it *precisely* the way it came off, otherwise you'll throw your
toe setting out.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
@n67g2000cwd.googlegroups.com:
> I just failed VA inspection because my right front rack boot is torn.
> Can I replace the boot myself?
>
Yes. It requires removal of the outer tie rod end.
When removing make 100% certain you count the threads and make sure you
reinstall it *precisely* the way it came off, otherwise you'll throw your
toe setting out.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
12-13-2006 | 06:45 PM
#4
Guest
Posts: n/a
Re: 1990 accord torn rack boot
etoyfixers@gmail.com wrote in news:1166040842.197701.272950
@n67g2000cwd.googlegroups.com:
> I just failed VA inspection because my right front rack boot is torn.
> Can I replace the boot myself?
>
Yes. It requires removal of the outer tie rod end.
When removing make 100% certain you count the threads and make sure you
reinstall it *precisely* the way it came off, otherwise you'll throw your
toe setting out.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
@n67g2000cwd.googlegroups.com:
> I just failed VA inspection because my right front rack boot is torn.
> Can I replace the boot myself?
>
Yes. It requires removal of the outer tie rod end.
When removing make 100% certain you count the threads and make sure you
reinstall it *precisely* the way it came off, otherwise you'll throw your
toe setting out.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
12-13-2006 | 06:45 PM
#5
Guest
Posts: n/a
Re: 1990 accord torn rack boot
etoyfixers@gmail.com wrote in news:1166040842.197701.272950
@n67g2000cwd.googlegroups.com:
> I just failed VA inspection because my right front rack boot is torn.
> Can I replace the boot myself?
>
Yes. It requires removal of the outer tie rod end.
When removing make 100% certain you count the threads and make sure you
reinstall it *precisely* the way it came off, otherwise you'll throw your
toe setting out.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
@n67g2000cwd.googlegroups.com:
> I just failed VA inspection because my right front rack boot is torn.
> Can I replace the boot myself?
>
Yes. It requires removal of the outer tie rod end.
When removing make 100% certain you count the threads and make sure you
reinstall it *precisely* the way it came off, otherwise you'll throw your
toe setting out.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
12-13-2006 | 08:04 PM
#6
Guest
Posts: n/a
Re: 1990 accord torn rack boot
Tegger wrote:
>
> etoyfixers@gmail.com wrote in news:1166040842.197701.272950
> @n67g2000cwd.googlegroups.com:
>
> > I just failed VA inspection because my right front rack boot is torn.
> > Can I replace the boot myself?
> >
>
> Yes. It requires removal of the outer tie rod end.
>
> When removing make 100% certain you count the threads and make sure you
> reinstall it *precisely* the way it came off, otherwise you'll throw your
> toe setting out.
>
When I replaced both of the rack boots on my '88 Civic, in addition to
counting the threads, I put punch marks on the bottom of tie rods. This
provided me with a second reference point which helped ensure that the toe
adjustment was exactly the same as it was before disassembly. I later ran
the car over a computerized slide slip tester which confirmed that the toe
setting did not change after replacing the boots. If you don't want to put
punch marks on the tie rods, then you could probably also get by using a
permanent marker such as a Sharpie (since if you get front end work done in
the future the punch marks may no longer be relevant).
Eric
>
> etoyfixers@gmail.com wrote in news:1166040842.197701.272950
> @n67g2000cwd.googlegroups.com:
>
> > I just failed VA inspection because my right front rack boot is torn.
> > Can I replace the boot myself?
> >
>
> Yes. It requires removal of the outer tie rod end.
>
> When removing make 100% certain you count the threads and make sure you
> reinstall it *precisely* the way it came off, otherwise you'll throw your
> toe setting out.
>
When I replaced both of the rack boots on my '88 Civic, in addition to
counting the threads, I put punch marks on the bottom of tie rods. This
provided me with a second reference point which helped ensure that the toe
adjustment was exactly the same as it was before disassembly. I later ran
the car over a computerized slide slip tester which confirmed that the toe
setting did not change after replacing the boots. If you don't want to put
punch marks on the tie rods, then you could probably also get by using a
permanent marker such as a Sharpie (since if you get front end work done in
the future the punch marks may no longer be relevant).
Eric
12-13-2006 | 08:04 PM
#7
Guest
Posts: n/a
Re: 1990 accord torn rack boot
Tegger wrote:
>
> etoyfixers@gmail.com wrote in news:1166040842.197701.272950
> @n67g2000cwd.googlegroups.com:
>
> > I just failed VA inspection because my right front rack boot is torn.
> > Can I replace the boot myself?
> >
>
> Yes. It requires removal of the outer tie rod end.
>
> When removing make 100% certain you count the threads and make sure you
> reinstall it *precisely* the way it came off, otherwise you'll throw your
> toe setting out.
>
When I replaced both of the rack boots on my '88 Civic, in addition to
counting the threads, I put punch marks on the bottom of tie rods. This
provided me with a second reference point which helped ensure that the toe
adjustment was exactly the same as it was before disassembly. I later ran
the car over a computerized slide slip tester which confirmed that the toe
setting did not change after replacing the boots. If you don't want to put
punch marks on the tie rods, then you could probably also get by using a
permanent marker such as a Sharpie (since if you get front end work done in
the future the punch marks may no longer be relevant).
Eric
>
> etoyfixers@gmail.com wrote in news:1166040842.197701.272950
> @n67g2000cwd.googlegroups.com:
>
> > I just failed VA inspection because my right front rack boot is torn.
> > Can I replace the boot myself?
> >
>
> Yes. It requires removal of the outer tie rod end.
>
> When removing make 100% certain you count the threads and make sure you
> reinstall it *precisely* the way it came off, otherwise you'll throw your
> toe setting out.
>
When I replaced both of the rack boots on my '88 Civic, in addition to
counting the threads, I put punch marks on the bottom of tie rods. This
provided me with a second reference point which helped ensure that the toe
adjustment was exactly the same as it was before disassembly. I later ran
the car over a computerized slide slip tester which confirmed that the toe
setting did not change after replacing the boots. If you don't want to put
punch marks on the tie rods, then you could probably also get by using a
permanent marker such as a Sharpie (since if you get front end work done in
the future the punch marks may no longer be relevant).
Eric
12-13-2006 | 08:04 PM
#8
Guest
Posts: n/a
Re: 1990 accord torn rack boot
Tegger wrote:
>
> etoyfixers@gmail.com wrote in news:1166040842.197701.272950
> @n67g2000cwd.googlegroups.com:
>
> > I just failed VA inspection because my right front rack boot is torn.
> > Can I replace the boot myself?
> >
>
> Yes. It requires removal of the outer tie rod end.
>
> When removing make 100% certain you count the threads and make sure you
> reinstall it *precisely* the way it came off, otherwise you'll throw your
> toe setting out.
>
When I replaced both of the rack boots on my '88 Civic, in addition to
counting the threads, I put punch marks on the bottom of tie rods. This
provided me with a second reference point which helped ensure that the toe
adjustment was exactly the same as it was before disassembly. I later ran
the car over a computerized slide slip tester which confirmed that the toe
setting did not change after replacing the boots. If you don't want to put
punch marks on the tie rods, then you could probably also get by using a
permanent marker such as a Sharpie (since if you get front end work done in
the future the punch marks may no longer be relevant).
Eric
>
> etoyfixers@gmail.com wrote in news:1166040842.197701.272950
> @n67g2000cwd.googlegroups.com:
>
> > I just failed VA inspection because my right front rack boot is torn.
> > Can I replace the boot myself?
> >
>
> Yes. It requires removal of the outer tie rod end.
>
> When removing make 100% certain you count the threads and make sure you
> reinstall it *precisely* the way it came off, otherwise you'll throw your
> toe setting out.
>
When I replaced both of the rack boots on my '88 Civic, in addition to
counting the threads, I put punch marks on the bottom of tie rods. This
provided me with a second reference point which helped ensure that the toe
adjustment was exactly the same as it was before disassembly. I later ran
the car over a computerized slide slip tester which confirmed that the toe
setting did not change after replacing the boots. If you don't want to put
punch marks on the tie rods, then you could probably also get by using a
permanent marker such as a Sharpie (since if you get front end work done in
the future the punch marks may no longer be relevant).
Eric
12-13-2006 | 08:04 PM
#9
Guest
Posts: n/a
Re: 1990 accord torn rack boot
Tegger wrote:
>
> etoyfixers@gmail.com wrote in news:1166040842.197701.272950
> @n67g2000cwd.googlegroups.com:
>
> > I just failed VA inspection because my right front rack boot is torn.
> > Can I replace the boot myself?
> >
>
> Yes. It requires removal of the outer tie rod end.
>
> When removing make 100% certain you count the threads and make sure you
> reinstall it *precisely* the way it came off, otherwise you'll throw your
> toe setting out.
>
When I replaced both of the rack boots on my '88 Civic, in addition to
counting the threads, I put punch marks on the bottom of tie rods. This
provided me with a second reference point which helped ensure that the toe
adjustment was exactly the same as it was before disassembly. I later ran
the car over a computerized slide slip tester which confirmed that the toe
setting did not change after replacing the boots. If you don't want to put
punch marks on the tie rods, then you could probably also get by using a
permanent marker such as a Sharpie (since if you get front end work done in
the future the punch marks may no longer be relevant).
Eric
>
> etoyfixers@gmail.com wrote in news:1166040842.197701.272950
> @n67g2000cwd.googlegroups.com:
>
> > I just failed VA inspection because my right front rack boot is torn.
> > Can I replace the boot myself?
> >
>
> Yes. It requires removal of the outer tie rod end.
>
> When removing make 100% certain you count the threads and make sure you
> reinstall it *precisely* the way it came off, otherwise you'll throw your
> toe setting out.
>
When I replaced both of the rack boots on my '88 Civic, in addition to
counting the threads, I put punch marks on the bottom of tie rods. This
provided me with a second reference point which helped ensure that the toe
adjustment was exactly the same as it was before disassembly. I later ran
the car over a computerized slide slip tester which confirmed that the toe
setting did not change after replacing the boots. If you don't want to put
punch marks on the tie rods, then you could probably also get by using a
permanent marker such as a Sharpie (since if you get front end work done in
the future the punch marks may no longer be relevant).
Eric
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)