FS 1990 BMW 325i Turbo E30
#1
FS 1990 BMW 325i Turbo E30
I'm posting for a friend. Please email or call the number below. The car is a 1990 325 I , The chassis is very clean. the only rust are is one corner of the battery tray. Everything after the front fenders is clean, the hood has some rust so does the sunroof panel ( I have a new one ). The car has never been in any accidents.
Here is a list of the things that were done under 10k ago.
Main bearings and bolts
Rod bearings and bolts
Piston rings
Head bolts
All seals and gaskets
Turbo back 3inch exhaust with Magnaflow muffler, high flow cat and tips
Timing belt
Water pump
Clutch
Transmission
Oil cooler and lines
Engine mounts
Transmission mounts
Rear shock mounts
All turbo related components
MS and wiring
Here is a list of things that were done in the last few years.
Bilsien shock front and back
Springs (Eiback)
Short Shifter (B&M)
Wheels and tires
Here is a list of things that are needed
The emergency brake system is not working, it needs the rear cables and shoes.
Driver side front wheel bearing.
Rear sub frame bushings.
The car was dyno tunned at Tag Race Craft right after the break in, it put down 330whp and 325wtq, it was also street tunned extensively for good daily driving.
It also ran a 13.3 @ 113 mph at TMSP last month.
The car is an absolute blast to drive and its not easy letting it go but for now this is the right thing to do.
I have a ton of extra parts that come with the car as well, including a set for 4piston calipers, cylinder head, stock intake manifold ect.
Now for the price. I realize it would be unrealistic if I ask for every penny I have put into the car, not to mention the amount of labor I have put into it so keeping that in mind I'm gonna start with an asking price for $ 7800 OBO which I think is a fair price.
You can get in touch with me by PM or my email address waleed_sadaqat@hotmail.com or by phone @ 647-448-3166
YouTube - Turbo E30, 2.7L Stroker 330+ WHP
Here is a list of the things that were done under 10k ago.
Main bearings and bolts
Rod bearings and bolts
Piston rings
Head bolts
All seals and gaskets
Turbo back 3inch exhaust with Magnaflow muffler, high flow cat and tips
Timing belt
Water pump
Clutch
Transmission
Oil cooler and lines
Engine mounts
Transmission mounts
Rear shock mounts
All turbo related components
MS and wiring
Here is a list of things that were done in the last few years.
Bilsien shock front and back
Springs (Eiback)
Short Shifter (B&M)
Wheels and tires
Here is a list of things that are needed
The emergency brake system is not working, it needs the rear cables and shoes.
Driver side front wheel bearing.
Rear sub frame bushings.
The car was dyno tunned at Tag Race Craft right after the break in, it put down 330whp and 325wtq, it was also street tunned extensively for good daily driving.
It also ran a 13.3 @ 113 mph at TMSP last month.
The car is an absolute blast to drive and its not easy letting it go but for now this is the right thing to do.
I have a ton of extra parts that come with the car as well, including a set for 4piston calipers, cylinder head, stock intake manifold ect.
Now for the price. I realize it would be unrealistic if I ask for every penny I have put into the car, not to mention the amount of labor I have put into it so keeping that in mind I'm gonna start with an asking price for $ 7800 OBO which I think is a fair price.
You can get in touch with me by PM or my email address waleed_sadaqat@hotmail.com or by phone @ 647-448-3166
YouTube - Turbo E30, 2.7L Stroker 330+ WHP
#5
You should know, I am in love with this car. I check this site a few times a week for the classified's because I plan on buying a new car in the summer and this is by far my favorite thing ive seen yet.
I have to ask though, whats it like on gas?
I have to ask though, whats it like on gas?
Thread
Thread Starter
Forum
Replies
Last Post
honda video
Honda Videos
0
07-21-2008 12:53 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)