Civic Turbo and misc parts *very long list :D
03-03-2005 | 03:40 PM
#1
Thread Starter
~~ Hardcore Newb ~~
Joined: Feb 2005
Posts: 55
From: Ottawa
Rep Power: 722 
Civic Turbo and misc parts *very long list :D
J.G. Engine Dynamics PRO-SERIES Cylinder Head. (not the crappy redline series,
this is the best of the best PRO SERIES), designed for high flow or turbo
application, flow bench tested and built at JG headquarters in California, JG
black nitrided stainless steel 0.5mm oversize valves, 9000RPM+ stiff single
wound JG Competition high rate valve springs, lightweight retainers, full turbo
port and polish, full radius intake competition valve job, 3 angle exhaust
competition valve job, new valve seals, minimum resurfacing, valued at over
2600$ after shipping and taxes, selling for less than half price at 1200$ obo with
original receipt, so lets make a deal.
!!!NEW PRICE!!! J.E. Pistons: Custom built D16Z6 race pistons, zero-silicon
aluminum turbo pistons built for 9.2:1 compression, able to handle up to 40 PSI
of boost, lightweight aluminum for less rotating mass and faster revving,
pistons are 240 grams each and matched for weight Part # 193607 (SPECS:
bore=2.963, stroke=3.543, flat top, comp. dist = 1.181, compression ration
9.2:1, Intake 0.220 measured from deck, Exhaust 0.155 measured from deck, groove
top 0.040, groove 2nd 0.048, groove bottom 0.111, land top 0.28, land 2nd 0.165,
land bottom 0.09, pin diameter 0.748, pin length 2.25, Dbl Spiro locks,. Set
clearance to 0.004, measure clearance 0.5 from bottom of piston skirt,) set is
including JE piston rings. Used for only 5000km. Selling set of 3, contact for
details, I have all the exact specs so that the other 1 can be ordered. Selling
3 JE pistons, just 150$
http://www3.sympatico.ca/torquemonst...tonsSpecs.jfif
!!! NEW PRICE!!! Eagle Connecting Rods, D16Z6 Race Rods, designed for handling
high boost or NOS and high rpms “ESP” forged steel H-beam design, part #
CRS5394H3D,(SPECS: C-C length 5.394”, total weight 510, rotating weight 371,
recipr weight 139, bolts 5/16” ARP 2000, Torque 28 ft/lbs w/ARP moly, bolt
stretch 0.0048”-0.0052”,) Matched for weight, handles 35+ PSI and 10000+RPM.
Selling set of 2, contact for details, I have all the exact specs so that the
other two identical ones can be ordered, selling two Eagle forged Connecting
Rods, just 100$
http://www3.sympatico.ca/torquemonst...odsspecs2.jfif
Chipped P28 ECU, save tons of money on labour installing your own soldering your
own piggyback into the motherboard and installing chip, already done for you,
300$
D16Z6 Clutchmasters clutch, Stage 3, Racing Carbon-Kevlar friction material,
Dual Spring, good condition, used for 3000km 450$
http://www3.sympatico.ca/torquemonst...tage3.jpeg.jpg
Turbosmart Pro-gate 45mm External Wastegate, investment cast Duplex Stainless
Steel Alloy body, 17-7 PH spring 7 p.s.i. spring for durability under extreme
temperature, cast stainless steel Vee band adapter kit, high grade reinforced
Silicon Nomex diaphragm, diaphragm housing billet 6061 T6 aluminum, optimum
2.8:1 actuator to valve ratio for precise boost control, one piece valve for
strength and reliability, body and valve investment cast from 253MA stainless
steel for high strength and excellent resistance to oxidation, creep deformation
and wear, and temperatures beyond 1200C, temperature isolation zone to reduce
heat transfer, 600$
Venom high-flow intake manifold, blue # M21-331, great for turbo NOS or high RPM
applications that require as much as in the engine as possible, CNC machined
billet 6061 T-6 aluminum, machined head flange and runners to reduce turbulence
to increase speed and volume of air movement and to insure 100% volumetric
efficiency of intake manifold, large round plenum, aluminum air intake reservoir
causes a billow effect pulling air into and pushing equal volumes into each
runner, anodized blue, intake runners smoothed for max air flow and decreased
turbulence, rewelded fuel rail mounts for maximum durability, throttle cable
bracket added, excess ports on back of manifold added for all sensors, MAP
sensor has its own unshared pressure source, 500$
D16Z6 dipstick, metal part is in perfect condition, the rubber circle grip is
blackened and not good condition, but it still works fine, just doesn’t look
pretty, 5$, or a second dipstick, better condition 10$
MSD RPM modules / pills for the MSD 6 series ignition or shift light, plug n’
play for your engines rev limit or for setting your shift light, 7000, 7200,
7400, 7600, 7800, rev/shift limits available. 10$ each OR TRADE for an 8000 RPM
pill
Civic or Integra adjustable springs coilovers, two are Tom’s and two are
Dropzone (used different brands to get the front/rear spring rates for desired
oversteer characteristics) 450springrate rear, 600springrate front, adjust ride
height from stock to 5 inch drop, 300$
Crower D16 Turbo VTEC cam, part #63441T-Z, stage 2, designed specifically for
turbo charged applications, features short duration and high lift, duration
260/238, duration @ 0.050” 222/200, gross lift w/1.6 int / 1.8 exh 430/428,
turbo grind features short duration, low overlap and high lift for optimum
performance, brand new 700$ now selling dirt cheap at 250$
Honda OEM Thermostat 15$
Honda OEM Thermostat housing 10$ or 20$ including thermostat
turbo T3/exhaust manifold gasket, 2 of them available 10$/each
D16 alternator, perfect working condition, 50$
AC Delco battery, 3 years old, fits civics, integras, etc. 40$
Acura ‘A’ symbol centre caps for rims, 4 of them, mint condition, 30$ for all of
them
D16 Driver side OEM rear rubber fender protector, looks like a thin long 2ft
piece of rubber that presses onto the edge of your fender, protects the edge of
the fender liner from getting chipped and developing rust 5$
D16Z6 power steering rack, 50$
D16 OEM pulleys, crank pulley, etc. 10$ each
Two (2) Bridgestone Potenza tires, 185/60/14 (standard 92-95 civic size), about
40% tread left, 25$ each, You can't go wrong at this price
Perfect working Master Cylinder, Booster and Proportioning Valve OEM from 92-95
Civic Si. Asking ONLY 150$ for EVERYTHING or best offer given will be accepted.
92-95 Black Civic Dashboard....includes the large main entire dashboard (all
clusters, gauges, airbags, etc. removed), the grey plastic console that goes
around the steering wheel area (the piece that has the buttons for cruise
control, fog lights, blanks, etc), the black lower console (that has ashtray,
cointray, lighter, etc). 50$
OEM Valve cover, Black, VTEC, perfect candidate for chroming, powdercoat, polish
or paint, or leave as is with good condition nice BLACK finish and Honda H logo
and HONDA written across it 40$
D16Z6 intake manifold 40$
D16Z6 throttle body 40$
http://www3.sympatico.ca/torquemonst...le/IMandTB.jpg
D16 fuel injectors 15$
http://www3.sympatico.ca/torquemonst...linjectors.jpg
D16Z6 VTEC cam 40$ and cam gear 10$
D16 shift linkage 20$
Heatshield for D16 exhaust manifold, 10$ or 5$ with purchase of anything else
http://www3.sympatico.ca/torquemonst...xhmanifold.jpg
D16 Head studs and head bolts OEM, complete set 20$
http://www3.sympatico.ca/torquemonst...boltsstuds.jpg
D16 stock pistons and D16 stock rods, perfect working condition, buy seperately
or together, pistons originally 9.2:1 in D16Z6 engine, higher compression when
put in D16Y8 engine, 60$/60$ to part, or buy piston and rod set for 95$.
AEM license plate cover, black with white writing, brand new and never used, 8$
http://www3.sympatico.ca/torquemonst...aemlicense.jpg
Momo Cobra shift ****, polished aluminum and genuine zebrano wood, momo insignia
embedded within, missing bolt cover at bottom 15$
http://www3.sympatico.ca/torquemonst...ocobraknob.jpg
D16 or B16 or D15 or B18B special distributor cap and rotor for mandatory use
with MSD ignition setup, a cap and rotor that has 5 plug wire inputs (4 for your
spark plug wires, 1 for your MSD ignition external coil), a necessity to run an
MSD 6A, MSD 6AL, MSD 6BTM,etc. with an external coil setup, excellent condition
25$
D16 fuel pump, perfect working condition, the fuel pump filter I'll throw in for
free, 25$
Honda "H" red badge, 10$
http://www3.sympatico.ca/torquemonst...hondabadge.jpg
OEM shift lever, fits all 1988-00 Honda civics, and also can fit integras, the
threading is slightly messed up but it will still work 10$
http://www3.sympatico.ca/torquemonst...le/shifter.jpg
Spark plug gapping tool, gap your plugs to the perfect gap and adjust them for
optimal power for your modifications, also confirm they are factory set
correctly 5$
Mint condition D16 stock intake box, intake resonator, and intake piping,
including filter, 40$
GTS Blackout headlight covers, broken on top but you can be creative and get
them to hold, 10$
http://www3.sympatico.ca/torquemonst.../blackouts.jpg
this is the best of the best PRO SERIES), designed for high flow or turbo
application, flow bench tested and built at JG headquarters in California, JG
black nitrided stainless steel 0.5mm oversize valves, 9000RPM+ stiff single
wound JG Competition high rate valve springs, lightweight retainers, full turbo
port and polish, full radius intake competition valve job, 3 angle exhaust
competition valve job, new valve seals, minimum resurfacing, valued at over
2600$ after shipping and taxes, selling for less than half price at 1200$ obo with
original receipt, so lets make a deal.
!!!NEW PRICE!!! J.E. Pistons: Custom built D16Z6 race pistons, zero-silicon
aluminum turbo pistons built for 9.2:1 compression, able to handle up to 40 PSI
of boost, lightweight aluminum for less rotating mass and faster revving,
pistons are 240 grams each and matched for weight Part # 193607 (SPECS:
bore=2.963, stroke=3.543, flat top, comp. dist = 1.181, compression ration
9.2:1, Intake 0.220 measured from deck, Exhaust 0.155 measured from deck, groove
top 0.040, groove 2nd 0.048, groove bottom 0.111, land top 0.28, land 2nd 0.165,
land bottom 0.09, pin diameter 0.748, pin length 2.25, Dbl Spiro locks,. Set
clearance to 0.004, measure clearance 0.5 from bottom of piston skirt,) set is
including JE piston rings. Used for only 5000km. Selling set of 3, contact for
details, I have all the exact specs so that the other 1 can be ordered. Selling
3 JE pistons, just 150$
http://www3.sympatico.ca/torquemonst...tonsSpecs.jfif
!!! NEW PRICE!!! Eagle Connecting Rods, D16Z6 Race Rods, designed for handling
high boost or NOS and high rpms “ESP” forged steel H-beam design, part #
CRS5394H3D,(SPECS: C-C length 5.394”, total weight 510, rotating weight 371,
recipr weight 139, bolts 5/16” ARP 2000, Torque 28 ft/lbs w/ARP moly, bolt
stretch 0.0048”-0.0052”,) Matched for weight, handles 35+ PSI and 10000+RPM.
Selling set of 2, contact for details, I have all the exact specs so that the
other two identical ones can be ordered, selling two Eagle forged Connecting
Rods, just 100$
http://www3.sympatico.ca/torquemonst...odsspecs2.jfif
Chipped P28 ECU, save tons of money on labour installing your own soldering your
own piggyback into the motherboard and installing chip, already done for you,
300$
D16Z6 Clutchmasters clutch, Stage 3, Racing Carbon-Kevlar friction material,
Dual Spring, good condition, used for 3000km 450$
http://www3.sympatico.ca/torquemonst...tage3.jpeg.jpg
Turbosmart Pro-gate 45mm External Wastegate, investment cast Duplex Stainless
Steel Alloy body, 17-7 PH spring 7 p.s.i. spring for durability under extreme
temperature, cast stainless steel Vee band adapter kit, high grade reinforced
Silicon Nomex diaphragm, diaphragm housing billet 6061 T6 aluminum, optimum
2.8:1 actuator to valve ratio for precise boost control, one piece valve for
strength and reliability, body and valve investment cast from 253MA stainless
steel for high strength and excellent resistance to oxidation, creep deformation
and wear, and temperatures beyond 1200C, temperature isolation zone to reduce
heat transfer, 600$
Venom high-flow intake manifold, blue # M21-331, great for turbo NOS or high RPM
applications that require as much as in the engine as possible, CNC machined
billet 6061 T-6 aluminum, machined head flange and runners to reduce turbulence
to increase speed and volume of air movement and to insure 100% volumetric
efficiency of intake manifold, large round plenum, aluminum air intake reservoir
causes a billow effect pulling air into and pushing equal volumes into each
runner, anodized blue, intake runners smoothed for max air flow and decreased
turbulence, rewelded fuel rail mounts for maximum durability, throttle cable
bracket added, excess ports on back of manifold added for all sensors, MAP
sensor has its own unshared pressure source, 500$
D16Z6 dipstick, metal part is in perfect condition, the rubber circle grip is
blackened and not good condition, but it still works fine, just doesn’t look
pretty, 5$, or a second dipstick, better condition 10$
MSD RPM modules / pills for the MSD 6 series ignition or shift light, plug n’
play for your engines rev limit or for setting your shift light, 7000, 7200,
7400, 7600, 7800, rev/shift limits available. 10$ each OR TRADE for an 8000 RPM
pill
Civic or Integra adjustable springs coilovers, two are Tom’s and two are
Dropzone (used different brands to get the front/rear spring rates for desired
oversteer characteristics) 450springrate rear, 600springrate front, adjust ride
height from stock to 5 inch drop, 300$
Crower D16 Turbo VTEC cam, part #63441T-Z, stage 2, designed specifically for
turbo charged applications, features short duration and high lift, duration
260/238, duration @ 0.050” 222/200, gross lift w/1.6 int / 1.8 exh 430/428,
turbo grind features short duration, low overlap and high lift for optimum
performance, brand new 700$ now selling dirt cheap at 250$
Honda OEM Thermostat 15$
Honda OEM Thermostat housing 10$ or 20$ including thermostat
turbo T3/exhaust manifold gasket, 2 of them available 10$/each
D16 alternator, perfect working condition, 50$
AC Delco battery, 3 years old, fits civics, integras, etc. 40$
Acura ‘A’ symbol centre caps for rims, 4 of them, mint condition, 30$ for all of
them
D16 Driver side OEM rear rubber fender protector, looks like a thin long 2ft
piece of rubber that presses onto the edge of your fender, protects the edge of
the fender liner from getting chipped and developing rust 5$
D16Z6 power steering rack, 50$
D16 OEM pulleys, crank pulley, etc. 10$ each
Two (2) Bridgestone Potenza tires, 185/60/14 (standard 92-95 civic size), about
40% tread left, 25$ each, You can't go wrong at this price
Perfect working Master Cylinder, Booster and Proportioning Valve OEM from 92-95
Civic Si. Asking ONLY 150$ for EVERYTHING or best offer given will be accepted.
92-95 Black Civic Dashboard....includes the large main entire dashboard (all
clusters, gauges, airbags, etc. removed), the grey plastic console that goes
around the steering wheel area (the piece that has the buttons for cruise
control, fog lights, blanks, etc), the black lower console (that has ashtray,
cointray, lighter, etc). 50$
OEM Valve cover, Black, VTEC, perfect candidate for chroming, powdercoat, polish
or paint, or leave as is with good condition nice BLACK finish and Honda H logo
and HONDA written across it 40$
D16Z6 intake manifold 40$
D16Z6 throttle body 40$
http://www3.sympatico.ca/torquemonst...le/IMandTB.jpg
D16 fuel injectors 15$
http://www3.sympatico.ca/torquemonst...linjectors.jpg
D16Z6 VTEC cam 40$ and cam gear 10$
D16 shift linkage 20$
Heatshield for D16 exhaust manifold, 10$ or 5$ with purchase of anything else
http://www3.sympatico.ca/torquemonst...xhmanifold.jpg
D16 Head studs and head bolts OEM, complete set 20$
http://www3.sympatico.ca/torquemonst...boltsstuds.jpg
D16 stock pistons and D16 stock rods, perfect working condition, buy seperately
or together, pistons originally 9.2:1 in D16Z6 engine, higher compression when
put in D16Y8 engine, 60$/60$ to part, or buy piston and rod set for 95$.
AEM license plate cover, black with white writing, brand new and never used, 8$
http://www3.sympatico.ca/torquemonst...aemlicense.jpg
Momo Cobra shift ****, polished aluminum and genuine zebrano wood, momo insignia
embedded within, missing bolt cover at bottom 15$
http://www3.sympatico.ca/torquemonst...ocobraknob.jpg
D16 or B16 or D15 or B18B special distributor cap and rotor for mandatory use
with MSD ignition setup, a cap and rotor that has 5 plug wire inputs (4 for your
spark plug wires, 1 for your MSD ignition external coil), a necessity to run an
MSD 6A, MSD 6AL, MSD 6BTM,etc. with an external coil setup, excellent condition
25$
D16 fuel pump, perfect working condition, the fuel pump filter I'll throw in for
free, 25$
Honda "H" red badge, 10$
http://www3.sympatico.ca/torquemonst...hondabadge.jpg
OEM shift lever, fits all 1988-00 Honda civics, and also can fit integras, the
threading is slightly messed up but it will still work 10$
http://www3.sympatico.ca/torquemonst...le/shifter.jpg
Spark plug gapping tool, gap your plugs to the perfect gap and adjust them for
optimal power for your modifications, also confirm they are factory set
correctly 5$
Mint condition D16 stock intake box, intake resonator, and intake piping,
including filter, 40$
GTS Blackout headlight covers, broken on top but you can be creative and get
them to hold, 10$
http://www3.sympatico.ca/torquemonst.../blackouts.jpg
03-03-2005 | 03:41 PM
#2
Thread Starter
~~ Hardcore Newb ~~
Joined: Feb 2005
Posts: 55
From: Ottawa
Rep Power: 722
From a 92-95 D16 but will fit any D series or B series, mint condition steering
wheel with undeployed airbag and cartridge still in it, steering wheel and
airbag sold to you for 100$
http://www3.sympatico.ca/torquemonst...withairbag.jpg
20W-50 AMSOIlL Series 2000 Servere Service Racing Oil, this is the best of the
best, 320 Celcius, racing stabilizers, full premium grade synthetic, red in
colour, extremely hard to find and hard to get, low coefficient of drag for
highest power output, look it up on AMSOIL website for more about how good this
oil is. For serious engines with serious mods who want the best protection money
can buy. As much as you want, 13$/litre no tax.
http://www3.sympatico.ca/torquemonst...amsoilrace.jpg
Clear corner lens (one), 92-95 Civic, drivers side, 10$
http://www3.sympatico.ca/torquemonst...nerdrivers.jpg
OEM cruise control pedal switch, as a replacement or can be used for any clutch
pedal activated device, 20$
http://www3.sympatico.ca/torquemonst...edalswitch.jpg
OEM cruise control unit, the activation solenoid itself, 50$
OEM cruise control wire, 10$
92-95 Civic Power mirror, broken plastic, motor still is fine and glass is fine
if yours is broken 20$
http://www3.sympatico.ca/torquemonst...owermirror.jpg
D16Z6 OEM transmission differential, perfect condition. good to have if you like
to do those damn one wheel burnouts that fry your differential..40$
http://www3.sympatico.ca/torquemonst...fferential.jpg
OEM orange corner lenses from 92-95 civic 20$
http://www3.sympatico.ca/torquemonst...EMblinkers.jpg
P72 GSR complete uncut Japanese wiring harness 40$
GSR Air conditioning AC compressor 20$
GSR power steering pump 10$
D16 starter motor 20$
New GM 2 BAR (15 PSI) MAP sensor,G.M. part# 16254539 reads boost, brand new in
package, good for turbo applications to avoid using checkvalves on the Honda map
sensor, or for any turbo setup where you want to tune using boost instead of
just RPM, sells new for 125$-->STILL NEW, my price 50$
http://www3.sympatico.ca/torquemonst...RMAPsensor.jpg
ITR integra type-r EBC RED performance racing brake pads, BRAND NEW IN UNOPENED
BOX, 150$ no tax
MSD coil wire, connects from MSD coil to distributor 30$
B&M Oil Cooler Kit, includes all hoses, a filter, heat exchanging unit, remote
mount oil filter, engine bypass adapter, radiator mount kit…..180$
RC 440 injectors, supports well over 300+ horsepower…..contact for price
Greddy intercooler, LARGE FRONT-Mount, low-restriction, ITR/GSR model, light
weight aluminum, TRUST logos embossed in tank, contact for more details, one
year old, 1500$
Garret T3/T4 COMPETITION TURBO, custom built by famous automotive engineer Ola
Lynstroem, custom designed for high-boost, high-rpm engine output, custom specs,
PROVEN 300+ hp on D16, will work well for peak horsepower with B-series and
D-series (D16, B16, B18, B18C, B18C5, LS/VTEC, mini-me, B18C1), or as a
super-fast spool up on H-series and F-series (H22, H22A, F22, B20, or
frankenstein), all specifications, more info, flow characteristics, data,
graphs, dyno results, history, references, etc. are available. SERIOUS ENQUIRIES
ONLY. This is a top quality, race-spec, custom turbo and you get what you pay
for. Fast spool, low temps, high boost, what else can ask for? Contact for more
details 1600$
Greddy profec b wiring kit, unopened all plugs and connectors, 30$
Exhaust manifold/turbo bolts with holes in them so they can be wire tied not to
unwind, 20$
Autometer 2 3/8 gauge panel u-bracket, 5$
Energy Suspesion polyurethane bushings and stabilizer components, mix n'match
from open packes, for front control arms (16.3105G) 10$ for 92-95 civic and 94+
integra and Motor mount inserts (16.1105G) 10$ for del sol and 92-00 civic
Alpine 6” rear speaker mesh covers, 5$
Honda 92-95 civic owners manual 10$
2 d16 ashtrays 10$/each
For further details or technical questions: partsforsale@lycos.com
For sales information or to make a purchase: kieran3000@hotmail.com
oh and all lowballers will be ignored, prices were reduced significantly so if u feel like giving a stupid offer, expect a stupid reply
wheel with undeployed airbag and cartridge still in it, steering wheel and
airbag sold to you for 100$
http://www3.sympatico.ca/torquemonst...withairbag.jpg
20W-50 AMSOIlL Series 2000 Servere Service Racing Oil, this is the best of the
best, 320 Celcius, racing stabilizers, full premium grade synthetic, red in
colour, extremely hard to find and hard to get, low coefficient of drag for
highest power output, look it up on AMSOIL website for more about how good this
oil is. For serious engines with serious mods who want the best protection money
can buy. As much as you want, 13$/litre no tax.
http://www3.sympatico.ca/torquemonst...amsoilrace.jpg
Clear corner lens (one), 92-95 Civic, drivers side, 10$
http://www3.sympatico.ca/torquemonst...nerdrivers.jpg
OEM cruise control pedal switch, as a replacement or can be used for any clutch
pedal activated device, 20$
http://www3.sympatico.ca/torquemonst...edalswitch.jpg
OEM cruise control unit, the activation solenoid itself, 50$
OEM cruise control wire, 10$
92-95 Civic Power mirror, broken plastic, motor still is fine and glass is fine
if yours is broken 20$
http://www3.sympatico.ca/torquemonst...owermirror.jpg
D16Z6 OEM transmission differential, perfect condition. good to have if you like
to do those damn one wheel burnouts that fry your differential..40$
http://www3.sympatico.ca/torquemonst...fferential.jpg
OEM orange corner lenses from 92-95 civic 20$
http://www3.sympatico.ca/torquemonst...EMblinkers.jpg
P72 GSR complete uncut Japanese wiring harness 40$
GSR Air conditioning AC compressor 20$
GSR power steering pump 10$
D16 starter motor 20$
New GM 2 BAR (15 PSI) MAP sensor,G.M. part# 16254539 reads boost, brand new in
package, good for turbo applications to avoid using checkvalves on the Honda map
sensor, or for any turbo setup where you want to tune using boost instead of
just RPM, sells new for 125$-->STILL NEW, my price 50$
http://www3.sympatico.ca/torquemonst...RMAPsensor.jpg
ITR integra type-r EBC RED performance racing brake pads, BRAND NEW IN UNOPENED
BOX, 150$ no tax
MSD coil wire, connects from MSD coil to distributor 30$
B&M Oil Cooler Kit, includes all hoses, a filter, heat exchanging unit, remote
mount oil filter, engine bypass adapter, radiator mount kit…..180$
RC 440 injectors, supports well over 300+ horsepower…..contact for price
Greddy intercooler, LARGE FRONT-Mount, low-restriction, ITR/GSR model, light
weight aluminum, TRUST logos embossed in tank, contact for more details, one
year old, 1500$
Garret T3/T4 COMPETITION TURBO, custom built by famous automotive engineer Ola
Lynstroem, custom designed for high-boost, high-rpm engine output, custom specs,
PROVEN 300+ hp on D16, will work well for peak horsepower with B-series and
D-series (D16, B16, B18, B18C, B18C5, LS/VTEC, mini-me, B18C1), or as a
super-fast spool up on H-series and F-series (H22, H22A, F22, B20, or
frankenstein), all specifications, more info, flow characteristics, data,
graphs, dyno results, history, references, etc. are available. SERIOUS ENQUIRIES
ONLY. This is a top quality, race-spec, custom turbo and you get what you pay
for. Fast spool, low temps, high boost, what else can ask for? Contact for more
details 1600$
Greddy profec b wiring kit, unopened all plugs and connectors, 30$
Exhaust manifold/turbo bolts with holes in them so they can be wire tied not to
unwind, 20$
Autometer 2 3/8 gauge panel u-bracket, 5$
Energy Suspesion polyurethane bushings and stabilizer components, mix n'match
from open packes, for front control arms (16.3105G) 10$ for 92-95 civic and 94+
integra and Motor mount inserts (16.1105G) 10$ for del sol and 92-00 civic
Alpine 6” rear speaker mesh covers, 5$
Honda 92-95 civic owners manual 10$
2 d16 ashtrays 10$/each
For further details or technical questions: partsforsale@lycos.com
For sales information or to make a purchase: kieran3000@hotmail.com
oh and all lowballers will be ignored, prices were reduced significantly so if u feel like giving a stupid offer, expect a stupid reply
03-08-2005 | 06:27 PM
#15
~~ Hardcore Newb ~~
Joined: Mar 2005
Posts: 23
Rep Power: 719
Originally Posted by toalan
will the rods and pistions fit in a DOHC ZC? anyone can help?